FDC37M81x SMSC Corporation, FDC37M81x Datasheet - Page 130
FDC37M81x
Manufacturer Part Number
FDC37M81x
Description
PC98/99 Compliant Enhanced Super I/O Controller
Manufacturer
SMSC Corporation
Datasheet
1.FDC37M81X.pdf
(198 pages)
- Current page: 130 of 198
- Download datasheet (683Kb)
entering or exiting a sleep state or trigger false PME events. The FDC37M81x has “isolation” bits for
the keyboard and mouse signals, which allow the keyboard and mouse data signals to go into the
wakeup logic but block the keyboard clock and data signals and the mouse clock and data signals from
the 8042. These bits may be used when it is necessary to isolate the 8042 keyboard and mouse signals
from the 8042 before entering a system sleep state.
See the SMSC Application Note titled “Using the Enhanced Keyboard and Mouse Wakeup Feature in
SMSC Super I/O Parts” for more information.
The bits used to isolate the keyboard and mouse signals from the 8042 are located in Logical Device 7,
Register 0xF0 (KRST_GA20) and are defined as follows:
Bit[6] M_ISO. Enables/disables isolation of mouse signals into 8042. Does not affect the MDAT signal
to the mouse wakeup (PME) logic.
1= Block mouse clock and data signals into 8042
0= Do not block mouse clock and data signals into 8042
Bit[5] K_ISO. Enables/disables isolation of keyboard signals into 8042. Does not affect the KDAT
signal to the keyboard wakeup (PME) logic.
1= Block keyboard clock and data signals into 8042
0= Do not block keyboard clock and data signals into 8042
When the keyboard and/or mouse isolation bits are used, it may be necessary to reset the 8042 upon
exiting the sleep state. If either of the isolation bits is set prior to entering a sleep state where VCC goes
inactive (S3-S5), then the 8042 must be reset upon exiting the sleep mode. Write 0x40 to global
configuration register 0x2C to reset the 8042. The 8042 must then be taken out of reset by writing 0x00
to register 0x2C since the bit that resets the 8042 is not self-clearing. Caution: Bit 6 of configuration
register 0x2C is used to put the 8042 into reset - do not set any of the other bits in register 0x2C, as this
may produce undesired results.
It is not necessary to reset the 8042 if the isolation bits are used for a sleep state where VCC does not
go inactive (S1, S2).
130
Related parts for FDC37M81x
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
EMC Filters - Single-Phase Filters - FD/FDC/FDV IEC Connector Filter
Manufacturer:
Premo
Datasheet:
Part Number:
Description:
FD TYPE CONNECTOR FOR RIBBON CABLE
Manufacturer:
Hirose Electric
Datasheet:
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: