FDC37M81x SMSC Corporation, FDC37M81x Datasheet - Page 123
FDC37M81x
Manufacturer Part Number
FDC37M81x
Description
PC98/99 Compliant Enhanced Super I/O Controller
Manufacturer
SMSC Corporation
Datasheet
1.FDC37M81X.pdf
(198 pages)
- Current page: 123 of 198
- Download datasheet (683Kb)
Status Register
This register is cleared on a reset. This register is
read-only for the Host and read/write by the
FDC37M81x CPU.
UD
C/D
IBF
UD
D7
Writable by FDC37M81x CPU.
bits are user-definable.
(Command
whether the input data register contains
data or a command (0 = data, 1 =
command).
data/command write operation, this bit is
set to "1" if SA2 = 1 or reset to "0" if SA2
= 0.
(Input Buffer Full)- This flag is set to 1
whenever the host system writes data
into the input data register. Setting this
flag activates the FDC37M81x CPU's
nIBF (MIRQ) interrupt if enabled. When
the FDC37M81x CPU reads the input
data
automatically reset and the interrupt is
cleared.
associated with this internal signal.
KCLK
KDAT
MCLK
MDAT
Host I/F Data Reg
Host I/F Status Reg
register
UD
D6
There is no output pin
Data)-This
DESCRIPTION
(DBB),
During
UD
D5
bit
this
a
specifies
bit
N/A: Not Applicable
Table 50 - Resets
These
Table 49 - Status Register
UD
D4
host
is
123
HARDWARE RESET (RESET_DRV)
OBF
EXTERNAL CLOCK SIGNAL
The FDC37M81x Keyboard Controller clock
source is a 12 MHz clock generated from a 14.318
MHz clock. The reset pulse must last for at least
24 16 MHz clock periods.
requirement applies to both internally (Vcc POR)
and externally generated reset signals.
powerdown mode, the external clock signal is not
loaded by the chip.
DEFAULT RESET CONDITIONS
The FDC37M81x has one source of reset: an
external reset via the RESET_DRV pin. Refer to
Table 50 for the effect of each type of reset on the
internal registers.
C/D
D3
(Output Buffer Full) - This flag is set to
whenever the FDC37M81x CPU write to
the output data register (DBB). When the
host system reads the output data
register, this bit is automatically reset.
Weak High
Weak High
Weak High
Weak High
00H
N/A
UD
D2
IBF
D1
The pulse-width
OBF
D0
In
Related parts for FDC37M81x
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
EMC Filters - Single-Phase Filters - FD/FDC/FDV IEC Connector Filter
Manufacturer:
Premo
Datasheet:
Part Number:
Description:
FD TYPE CONNECTOR FOR RIBBON CABLE
Manufacturer:
Hirose Electric
Datasheet:
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: