ADUC7060 Analog Devices, ADUC7060 Datasheet - Page 28

• Manufacturer Part Number: ADUC7060
• Description: Low-Power, Precision Analog Microcontroller, Dual ?-? ADCs, Flash/EE, ARM7TDMI
• Manufacturer: Analog Devices

Specifications of ADUC7060

• Mcu Core: ARM7 TDMI
• Mcu Speed (mips): 10
• Sram (bytes): 4096Bytes
• Gpio Pins: 14
• Adc # Channels: 10
• Other: 14 Bit DAC,PWM

ADuC7060/ADuC7061
COMPLETE MMR LISTING
In the following MMR tables, addresses are listed in hexadecimal code. Access types include R for read, W for write, and R/W for read
and write.
Table 17. IRQ Address Base = 0xFFFF0000
Address
0x0000
0x0004
0x0008
0x000C
0x0010
0x0014
0x001C
0x0020
0x0024
0x0028
0x0030
0x0034
0x0038
0x003C
0x0100
0x0104
0x0108
0x010C
0x011C
0x013C
Table 18. System Control Address Base = 0xFFFF0200
Address
0x0220
0x0230
0x0234
1
Updated by the kernel.
Name
IRQSTA
IRQSIG
IRQEN
IRQCLR
SWICFG
IRQBASE
IRQVEC
IRQP0
IRQP1
IRQP2
IRQCONN
IRQCONE
IRQCLRE
IRQSTAN
FIQSTA
FIQSIG
FIQEN
FIQCLR
FIQVEC
FIQSTAN
Name
REMAP
RSTSTA
RSTCLR
1
Bytes
1
1
1
Bytes
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
R/W
R/W
Access
Type
R/W
R/W
W
Access
Type
R
R
W
W
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
R
R
R/W
W
R
R/W
0x00
0x00
Default Value
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
Default Value
0x01
Rev. C | Page 28 of 108
Description
Active IRQ source status.
Current state of all IRQ sources (enabled and disabled).
Enabled IRQ sources.
MMR to disable IRQ sources.
Software interrupt configuration MMR.
Base address of all vectors. Points to the start of the 64-byte memory block,
which can contain up to 32 pointers to separate subroutine handlers.
This register contains the subroutine address for the currently active
IRQ source.
Contains the interrupt priority setting for Interrupt Source 1 to Interrupt
Source 7. An interrupt can have a priority setting of 0 to 7.
Contains the interrupt priority setting for Interrupt Source 8 to Interrupt
Source 15.
Contains the interrupt priority setting for Interrupt Source 16 to
Interrupt Source 19.
Used to enable IRQ and FIQ interrupt nesting.
Configures the external interrupt sources as rising edge, falling edge, or
level triggered.
Used to clear an edge-level-triggered interrupt source.
This register indicates the priority level of an interrupt that has just
caused an interrupt exception.
Active FIQ source status.
Current state of all FIQ sources (enabled and disabled).
Enabled FIQ sources.
MMR to disable FIQ sources.
This register contains the subroutine address for the currently active FIQ
source.
Indicates the priority level of an FIQ that has just caused an FIQ
exception.
Description
Remap control register. See the Remap Operation section.
RSTSTA status MMR. See the Reset section.
Register for clearing the RSTSTA register.