ATxmega64A1 Atmel Corporation, ATxmega64A1 Datasheet - Page 338
ATxmega64A1
Manufacturer Part Number
ATxmega64A1
Description
Manufacturer
Atmel Corporation
Specifications of ATxmega64A1
Flash (kbytes)
64 Kbytes
Pin Count
100
Max. Operating Frequency
32 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
78
Ext Interrupts
78
Usb Speed
No
Usb Interface
No
Spi
12
Twi (i2c)
4
Uart
8
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
2000
Analog Comparators
4
Resistive Touch Screen
No
Dac Channels
4
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
AES/DES
Sram (kbytes)
4
Eeprom (bytes)
2048
Self Program Memory
YES
External Bus Interface
1
Dram Memory
sdram
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.6 to 3.6
Operating Voltage (vcc)
1.6 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
8
Output Compare Channels
24
Input Capture Channels
24
Pwm Channels
24
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATxmega64A1-AU
Manufacturer:
Atmel
Quantity:
135
Company:
Part Number:
ATxmega64A1U-AU
Manufacturer:
ATMEL
Quantity:
953
- Current page: 338 of 445
- Download datasheet (6Mb)
28.3
8077H–AVR–12/09
TAP - Test Access Port
When using the JTAG interface for Boundary-scan, the JTAG TCK clock frequency can be
higher than the internal device frequency. The System Clock in the device is not required for
Boundary-scan.
The JTAG interface is accessed through four of the AVR's pins. In JTAG terminology, these pins
constitute the Test Access Port - TAP. These pins are:
The IEEE std. 1149.1-2001 also specifies an optional TAP signal; TRST - Test ReSeT. This is
not available.
When the JTAGEN Fuse is unprogrammed or the JTAG Disable bit is set the JTAG interface is
disabled. The four TAP pins are normal port pins and the TAP controller is in reset. When
enabled, the input TAP signals are internally pulled high and the JTAG is enabled for Boundary-
scan operations.
Figure 28-1. TAP Controller state diagram
• TMS: Test mode select. This pin is used for navigating through the TAP-controller state
• TCK: Test Clock. JTAG operation is synchronous to TCK.
• TDI: Test Data In. Serial input data to be shifted in to the Instruction Register or Data Register
• TDO: Test Data Out. Serial output data from Instruction Register or Data Register.
machine.
(Scan Chains).
XMEGA A
338
Related parts for ATxmega64A1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: