ATxmega32A4U Atmel Corporation, ATxmega32A4U Datasheet - Page 78

• Manufacturer Part Number: ATxmega32A4U
• Manufacturer: Atmel Corporation

Specifications of ATxmega32A4U

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 7
• Twi (i2c): 2
• Uart: 5
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 4
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 5
• Output Compare Channels: 16
• Input Capture Channels: 16
• Pwm Channels: 16
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

6.8.2
8331A–AVR–07/11
CHnCTRL – Event Channel n Control Register
Table 6-4.
• Bit 7 – Reserved
This bit is reserved and will always be read as zero. For compatibility with future devices, always
write this bit to zero when this register is written.
• Bit 6:5 – QDIRM[1:0]: Quadrature Decode Index Recognition Mode
These bits determine the quadrature state for the QDPH0 and QDPH90 signals, where a valid
index signal is recognized and the counter index data event is given according to
page
nal is used.These bits are available only for CH0CTRL, CH2CTRL, and CH4CTRL.
Table 6-5.
• Bit 4 – QDIEN: Quadrature Decode Index Enable
When this bit is set, the event channel will be used as a QDEC index source, and the index data
event will be enabled.
This bit is available only for CH0CTRL, CH2CTRL, and CH4CTRL.
• Bit 3 – QDEN: Quadrature Decode Enable
Setting this bit enables QDEC operation.
This bit is available only for CH0CTRL, CH2CTRL, and CH4CTRL.
• Bit 2:0 – DIGFILT[2:0]: Digital Filter Coefficient
These bits define the length of digital filtering used. Events will be passed through to the event
channel only when the event source has been active and sampled with the same level for the
number of peripheral clock cycles defined by DIGFILT.
Bit
Read/Write
Initial Value
QDIRM[1:0]
T/C Event E
1
1
1
0
0
1
1
78. These bits should only be set when a quadrature encoder with a connected index sig-
0
1
1
0
1
0
1
1
0
1
Timer/counter events. (Continued)
QDIRM bit settings.
7
–
R
0
Index Recognition State
{QDPH0, QDPH90} = 0b00
{QDPH0, QDPH90} = 0b01
{QDPH0, QDPH90} = 0b10
{QDPH0, QDPH90} = 0b11
Group Configuration
TCxn_CCB
TCxn_CCC
TCxn_CCD
R/W
6
0
QDIRM[1:0]
R/W
5
0
Event Type
Capture or compare B (x = C, D, E or F) (n= 0 or 1)
Capture or compare C (x = C, D, E or F) (n= 0)
Capture or compare D (x = C, D, E or F) (n= 0)
QDIEN
R/W
4
0
QDEN
Atmel AVR XMEGA AU
R/W
3
0
R/W
2
0
DIGFILT[2:0]
R/W
1
0
R
0
0
Table 6-5 on
CHnCTRL
78