ATxmega32A4U Atmel Corporation, ATxmega32A4U Datasheet - Page 157

• Manufacturer Part Number: ATxmega32A4U
• Manufacturer: Atmel Corporation

Specifications of ATxmega32A4U

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 7
• Twi (i2c): 2
• Uart: 5
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 4
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 5
• Output Compare Channels: 16
• Input Capture Channels: 16
• Pwm Channels: 16
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

13.14.5
8331A–AVR–07/11
EBIOUT – EBI Output Register
Table 13-7 on page 157
Table 13-7.
• Bits 3:2 – CLKOUTSEL[1:0] : Clock Output Select
These bits are used to select which of the peripheral clocks will be output to the port pin if CLK-
OUT is configured.
Table 13-8.
• Bit 1:0 – CLKOUT[1:0]: Clock Output Port
These bits decide which port the peripheral clock will be output to. Pin 7 on the selected port is
the default used. The CLKOUT setting will override the EVOUT setting. Thus, if both are
enabled on the same port pin, the peripheral clock will be visible. The port pin must be config-
ured as output for the clock to be available on the pin.
Table 13-9 on page 157
Table 13-9.
• Bit 7:4 – Reserved
These bits are reserved and will always be read as zero. For compatibility with future devices,
always write these bits to zero when this register is written.
Bit
+0x05
Read/Write
Initial Value
CLKOUT[1:0]
00
01
10
11
CLKOUTSEL[1:0]
EVOUT[1:0]
00
01
10
11
00
01
10
R
7
–
0
Event output pin selection.
Event output clock selection.
Clock output port configurations.
R
6
–
0
shows the possible configurations.
shows the possible configurations.
Group Configuration
OFF
PC
PD
PE
Group Configuration
Group Configuration
CLK1X
CLK2X
CLK4X
R
5
–
0
OFF
PC
PD
PE
R
4
–
0
Description
Event output disabled
Event channel 0 output on PORTC
Event channel 0 output on PORTD
Event channel 0 output on PORTE
Description
CLK
CLK
CLK
Description
Clock output disabled
Clock output on PORTC
Clock output on PORTD
Clock output on PORTE
Atmel AVR XMEGA AU
R/W
EBIADROUT[1:0]
3
0
PER
PER2
PER4
output to pin
output to pin
output to pin
R/W
2
0
R/W
1
EBICSOUT[1:0]
0
R/W
0
0
CLKEVOUT
157