AT32UC3B1128 Atmel Corporation, AT32UC3B1128 Datasheet - Page 131

• Manufacturer Part Number: AT32UC3B1128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B1128

• Flash (kbytes): 128 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 28
• Ext Interrupts: 28
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

9.5.4.8
9.5.5
9.6
9.6.1
32002F–03/2010
Data Trace
Registers
Overview
Program Trace Correlation
Program Trace Correlation messages are used to correlate events to the program flow that may
not be associated with the instruction stream (e.g. Data Trace Messages). The occurrence of an
event listed in Table 9-41 will cause this message to be transmitted.
Table 9-41.
Table 9-42.
Program trace is enabled using the TM field in the Development Control register.
The AVR32 OCD system provides data trace via the AUX port. The CPU data memory accesses
can be monitored real-time using the Nexus class 2+ compliant Data Trace Unit. Both reads and
writes can be traced.
Data Trace information is transmitted through data trace messages, which can be of read or
write type, with or without sync. The messages contain information about the data address and
value which triggered the trace. Data addresses can be complete (with sync), or compressed
relative to the previous transmitted message (without sync). The value contains the data value
read or written from the data cache, and is of the same width as the access size (byte, halfword,
word, or doubleword).
The TM[1] bit in the Development Control register must be set to enable data trace. It is also
possible to trigger data trace using watchpoints. In this case, TM[1] will be set or cleared
automatically.
Program Trace Correlation
Size (bits)
8
4
6
Event Code
(EVCODE)
0b0000
0b0001
0b0010 - 0b0011
0b0100
0b0101 - 0b1111
Packet
Program Trace Correlation message
Event Code (EVCODE) description
Packet
Name
I-CNT
EVCODE
TCODE
Event Description
Entry into Debug Mode
Entry into Low Power Mode
Reserved
Program Trace Disabled
Reserved
Packet
Type
Variable
Fixed
Fixed
Direction: From target
Description
Number of instruction units executed since the last taken
branch.
Event Code. Refer to Table 9-42.
Value = 33
AVR32
131