M28529G-12 Mindspeed Technologies, M28529G-12 Datasheet - Page 295

• Manufacturer Part Number: M28529G-12
• Description: ATM IMA 8.192Mbps 1.8V/3.3V 484-Pin BGA
• Manufacturer: Mindspeed Technologies

Specifications of M28529G-12

• Package: 484BGA
• Utopia Type: Level 2
• Typical Operating Supply Voltage: 1.8|3.3 V
• Minimum Operating Supply Voltage: 1.71|3.135 V
• Maximum Operating Supply Voltage: 1.89|3.465 V
• Maximum Output Rate: 8.192 Mbps

Table 4-1.
Table 4-2.
Table 4-3.
28529-DSH-001-K
Comments: Maximum group size is 8 links.
Comments:
BIP.71
BIP.72
BIP.73
BIP.74
BIP.75
BIP.76
QOS.1
Item
Item
Item
CIT.1
CIT.2
CIT.3
CIT.4
CIT.5
CIT.6
CIT.7
Does the implementation support the Asymmetrical Configuration and
Operation mode?
Does the implementation abort the start-up procedure using the appropriate
code defined in the “Group Status and Control” field of the ICP cell (as
specified in Table 2 on page 31) if the NE does not support the symmetry
mode proposed by the FE?
Does the implementation abort the start-up procedure using the appropriate
code defined in the “Group Status and Control” field of the ICP cell (as
specified in Table 2 on page 31) if the symmetry mode proposed by the FE
and the configured symmetry mode of the NE do not match?
In order to allow a fast recovery when (O-5) or (O-6) is used at the NE and
when the FE IMA unit can only be configured to the “Symmetrical
Configuration and Operation” mode, does the implementation adjust to
“Symmetrical Configuration and Operation”.
Does the implementation support only the valid combinations of group
symmetry modes at each end of the IMA virtual link as specified in Table 4
on page 36?
Does the implementation allow configuration of the group mode?
Does the implementation support all ATM traffic/QoS classes supported by
the ATM layer?
Does the implementation indicate to the FE in which transmit clock mode it
is running in the “Transmit Clock Mode” field in the ICP cell?
Does the implementation support the CTC mode in the transmit direction?
Does the implementation only indicate to the FE that it is in the CTC mode
when all the “transmit” clocks of the links in the group are derived from the
same source?
Does the implementation support the ITC mode in the transmit direction?
Does the implementation indicate that it is in the ITC mode even if all the
transmit clocks of the links in the group are derived from the same source?
Does the implementation use the cell stuffing procedure to prevent link
transmit buffer under-run or over-run?
Does the implementation indicate a stuff event in the ICP cell preceding a
stuff event using the mandatory LSI codes specified in Table 2 on page 30?
Basic IMA Protocol (BIP) Definition Functions (5 of 5)
QoS Requirements Functions
CTC and ITC Operation Functions (1 of 2)
Protocol feature
Protocol feature
Protocol feature
Mindspeed Proprietary and Confidential
Mindspeed Technologies
®
(O-9)
Cond. for
Cond. for
Cond. for
Status
Status
Status
Status
Pred.
Status
Pred.
Status
M
M
M
O
O
O
Pred.
M
M
M
M
M
O
O
M
(O-6)
(R-52)
(R-52)
(O-7)
(R-53)
(O-8)
(R-55)
(R-56)
(R-57)
(O-9)
(O-10)
(CR-4)
(R-58)
(R-54)
Ref.
Ref.
Ref.
Yes X No__
Yes X No__
Yes X No__
Yes X No__
Yes X No__
Yes X No__
Yes X No__
Yes X No__
Yes X No__
Yes X No__
Yes X No__
Yes X No__
Yes X No__
Yes X No__
Appendices
Support
Support
Support
280