PIC16F1937-E/MV Microchip Technology, PIC16F1937-E/MV Datasheet - Page 64

• Manufacturer Part Number: PIC16F1937-E/MV
• Description: 14KB Flash, 512B RAM, 256B EEPROM, LCD, 1.8-5.5V 40 UQFN 5x5x0.5mm TUBE
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1937-E/MV

• Processor Series: PIC16F
• Core: PIC
• Program Memory Type: Flash
• Program Memory Size: 14 KB
• Data Ram Size: 256 B
• Interface Type: MI2C, SPI, EUSART
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Package / Case: UQFN-40
• Development Tools By Supplier: MPLAB IDE Software
• Minimum Operating Temperature: - 40 C
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Lead Free Status / Rohs Status: Details

PIC16(L)F1934/6/7
REGISTER 4-2:
DS41364E-page 64
bit 13
bit 6
Legend:
R = Readable bit
‘0’ = Bit is cleared
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7-6
bit 5-4
bit 3-2
bit 1-0
Note 1:
R/P-1/1
LVP
U-1
2:
3:
—
(1)
The LVP bit cannot be programmed to ‘0’ when Programming mode is entered via LVP.
Reads as ‘11’ on PIC16LF193X only.
The DEBUG bit in Configuration Word is managed automatically by device development tools including
debuggers and programmers. For normal device operation, this bit should be maintained as a ‘1’.
LVP: Low-Voltage Programming Enable bit
1 = Low-voltage programming enabled
0 = High-voltage on MCLR/V
DEBUG: In-Circuit Debugger Mode bit
1 = In-Circuit Debugger disabled, RB6/ICSPCLK and RB7/ICSPDAT are general purpose I/O pins
0 = In-Circuit Debugger enabled, RB6/ICSPCLK and RB7/ICSPDAT are dedicated to the debugger
Unimplemented: Read as ‘1’
BORV: Brown-out Reset Voltage Selection bit
1 = Brown-out Reset voltage set to 1.9V
0 = Brown-out Reset voltage set to 2.5V
STVREN: Stack Overflow/Underflow Reset Enable bit
1 = Stack Overflow or Underflow will cause a Reset
0 = Stack Overflow or Underflow will not cause a Reset
PLLEN: PLL Enable bit
1 = 4xPLL enabled
0 = 4xPLL disabled
Unimplemented: Read as ‘1’
VCAPEN<1:0>: Voltage Regulator Capacitor Enable bits
00 = V
01 = V
10 = V
11 = No capacitor on V
Unimplemented: Read as ‘1’
WRT<1:0>: Flash Memory Self-Write Protection bits
4 kW Flash memory PIC16(L)F1934 only):
8 kW Flash memory (PIC16(L)F1936 and PIC16(L)F1937 only):
DEBUG
R/P-1/1
R/P-1/1
11 = Write protection off
10 = 000h to 1FFh write-protected, 200h to FFFh may be modified by EECON control
01 = 000h to 7FFh write-protected, 800h to FFFh may be modified by EECON control
00 = 000h to FFFh write-protected, no addresses may be modified by EECON control
11 = Write protection off
10 = 000h to 1FFh write-protected, 200h to 1FFFh may be modified by EECON control
01 = 000h to FFFh write-protected, 1000h to 1FFFh may be modified by EECON control
00 = 000h to 1FFFh write-protected, no addresses may be modified by EECON control
CONFIGURATION WORD 2
CAP
CAP
CAP
VCAPEN<1:0>
(3)
functionality is enabled on RA0
functionality is enabled on RA5
functionality is enabled on RA6
P = Programmable bit
‘1’ = Bit is set
R/P-1/1
(2)
U-1
—
CAP
pin
PP
must be used for programming
R/P-1/1
BORV
(3)
U-1
—
(1)
-n = Value when blank or after Bulk Erase
U = Unimplemented bit, read as ‘1’
STVREN
R/P-1/1
U-1
(2)
—
 2008-2011 Microchip Technology Inc.
R/P-1/1
R/P-1/1
PLLEN
WRT1
R/P-1/1
WRT0
U-1
—
bit 7
bit 0