MTCMR-H4-P1-GB/IE Multi-Tech Systems, MTCMR-H4-P1-GB/IE Datasheet - Page 93

• Manufacturer Part Number: MTCMR-H4-P1-GB/IE
• Description: MODEM CELLULAR QUAD GPRS HSPA
• Manufacturer: Multi-Tech Systems
• Series: MultiModem® iCellr

Specifications of MTCMR-H4-P1-GB/IE

• Function: Transceiver, HSPA, Modem
• Modulation Or Protocol: GPRS, GSM, EDGE
• Frequency: 850MHz, 900MHz, 1.8GHz, 1.9GHz
• Applications: General Purpose
• Interface: RS-232, USB
• Data Rate - Maximum: 7.2 Mbps
• Features: UK Power Cord
• Voltage - Supply: 9 V ~ 32 V, USB
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 881-1122

+CGEQREQ 3G Quality of Service Profile (Requested)
High Speed HSPA-H4 AT Commands Reference Guide (Document S000483A)
Note:
Description:
Syntax:
Test Command:
Test Response:
Read Command:
Read Response:
All QOS settings will be stored non volatile.
[+CGEQREQ: ...]
<Traffic handling priority>
<PDP_type>
The test command returns values supported as a compound value.
The read command returns the current settings for each defined context for which QOS
was explicitly specified.
The write command allows the TE to specify a Quality of Service Profile for the context
identified by the (local) context identification parameter <cid> which is used when the
MT sends an Activate PDP Context Request message to the network.
A special form of the write command, AT+CGEQREQ=<cid> causes the requested
profile for context number <cid> to become undefined.
AT+CGEQREQ=?
+CGEQREQ : <PDP_type>, (list of supported <Traffic class>s), (list of supported
<Maximum bitrate UL>s), (list of supported <Maximum bitrate DL>s), (list of supported
<Guaranteed bitrate UL>s), (list of supported <Guaranteed bitrate DL>s), (list of
supported <Delivery order>s), (list of supported <Maximum SDU size>s), (list of
supported <SDU error ratio>s), (list of supported <Residual bit error ratio>s), (list of
supported <Delivery of erroneous SDUs>s), (list of supported <Transfer delay>s), (list of
supported <Traffic handling priority>s)
OK
AT+CGEQREQ?
+CGEQREQ: [<cid>, <Traffic class>, <Maximum bitrate UL>, <Maximum bitrate DL>,
<Guaranteed bitrate UL>, <Guaranteed bitrate DL>, <Delivery order>, <Maximum SDU
size>, <SDU error ratio>, <Residual bit error ratio>, <Delivery of erroneous SDUs>,
<Transfer delay>, <Traffic handling priority>]
[+CGEQREQ: <cid>, <Traffic class>, <Maximum bitrate UL>, <Maximum bitrate DL>,
<Guaranteed bitrate UL>, <Guaranteed bitrate DL>, <Delivery order>, <Maximum SDU
size>, <SDU error ratio>, <Residual bit error ratio>, <Delivery of erroneous SDUs>,
<Transfer delay>, <Traffic handling priority>]
0
10...150
200...950
1000...4000 (value needs to be divisible by 100 without remainder)
This parameter specifies the relative importance for handling of all SDUs belonging
to the UMTS bearer compared to the SDUs of the other bearers.
0
1
2
3
Packet Data Protocol Type
“IP“ Internet Protocol (IETF STD 5)
Default. Subscribed value.
Default. subscribed
(value needs to be divisible by 10 without remainder)
(value needs to be divisible by 50 without remainder)
Chapter 3 – Supported GSM/WCDMA AT Commands
93