MTCMR-H4-P1-GB/IE Multi-Tech Systems, MTCMR-H4-P1-GB/IE Datasheet - Page 125

• Manufacturer Part Number: MTCMR-H4-P1-GB/IE
• Description: MODEM CELLULAR QUAD GPRS HSPA
• Manufacturer: Multi-Tech Systems
• Series: MultiModem® iCellr

Specifications of MTCMR-H4-P1-GB/IE

• Function: Transceiver, HSPA, Modem
• Modulation Or Protocol: GPRS, GSM, EDGE
• Frequency: 850MHz, 900MHz, 1.8GHz, 1.9GHz
• Applications: General Purpose
• Interface: RS-232, USB
• Data Rate - Maximum: 7.2 Mbps
• Features: UK Power Cord
• Voltage - Supply: 9 V ~ 32 V, USB
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 881-1122

+CPIN Enter PIN
High Speed HSPA-H4 AT Commands Reference Guide (Document S000483A)
Description:
Syntax:
Values:
Parameter Storage: None
Examples:
This command is used to enter the mobile equipment passwords (PIN1/CHV1, PIN2/CHV2,
PUK1, PUK2, etc.) that are required before any mobile equipment functionality can be used.
PIN1/CHV1 and PIN2/CHV2 are between 4 and 8 digits long; PUK1 and PUK2 are only 8
digits long.
After three unsuccessful attempts to enter the PIN, the PUK will be required. PUK validation
forces the user to enter a new PIN code as a second parameter and this will be the new PIN
code if PUK validation succeeds. PIN 1/CHV 1 is then enabled if PUK1 is correct.
The application is responsible for checking the PIN after each reset or power on if the PIN
was enabled.
No Test Command
<NewPin> Personal Identification Number.
The response "+CME ERROR: 13" (SIM failure) is returned after 10 unsuccessful PUK
attempts. The SIM card is then out of order and must be replaced.
<pin>
<code>
Command
Action Command:
AT+CPIN=<pin>
[,<NewPin>]
Read Command:
AT+CPIN?
Command
AT+CPIN=1234
Note: Enter PIN
AT+CPIN=5678
Note: Enter PIN
AT+CPIN=00000000,1234
Note: Enter PUK and new PIN
AT+CPIN=12345678,1234
Note: Enter PUK and new PIN, 2nd
attempt
This parameter is required if the PIN state is SIM PUK.
Four to eight digit numbers.
Personal Identification Number.
Normally PIN1/CHV/
According to AT+CPIN?, the <pin> parameter can be PUK 1, PH-SIM PIN, PH-
NET PIN, PH-NETSUB PIN, PH-SERVPROV PIN, PH-CORPORATE PIN
Four to eight digit numbers.
SIM Code Status
READY
password
SIM PIN
SIM PUK
SIM PIN2
SIM PUK2
PH-SIM PIN
PH-NET PIN
PH-NETSUB PIN
PH- SERVPROV PIN
PH- CORPORATE PIN
Responses
OK
+CPIN: <code>
Note: No "OK"
Mobile equipment (ME) is not writing for any
PIN 1/CHV 1 is required
PUK1 is required
PIN 2/CHV 2 is required
PUK2 is required
SIM lock (phone-to-SIM) is required
Network personalization is required
Network subset is required
Service provider is required
Corporate is required
Chapter 3 – Supported GSM/WCDMA AT Commands
Responses
OK
Note: PIN code is correct
+CME ERROR: 3
Note: Operation not allowed, PIN previously
entered
+CME ERROR: 16
OK
Note: PUK correct, new PIN stored
Note: Incorrect PUK
125