MFRC53101T/0FE,112 NXP Semiconductors, MFRC53101T/0FE,112 Datasheet - Page 75
![IC MIFARE HS READER 32-SOIC](/photos/7/0/70098/568-32-soic_sot287-1_sml.jpg)
MFRC53101T/0FE,112
Manufacturer Part Number
MFRC53101T/0FE,112
Description
IC MIFARE HS READER 32-SOIC
Manufacturer
NXP Semiconductors
Series
MIFARE®r
Specifications of MFRC53101T/0FE,112
Rf Type
Read Only
Frequency
13.56MHz
Features
ISO14443-A, ISO14443-B, ISO15693
Package / Case
32-SOIC (0.300", 7.50mm Width)
Product
RFID Readers
Operating Temperature Range
- 25 C to + 85 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
568-2224-5
935269691112
MFRC531
MFRC53101TD
935269691112
MFRC531
MFRC53101TD
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MFRC53101T/0FE,112
Manufacturer:
NXP/恩智浦
Quantity:
20 000
NXP Semiconductors
MFRC531_34
Product data sheet
PUBLIC
11.1.1 Basic states
11.1.2 StartUp command 3Fh
11.1.3 Idle command 00h
Table 130. StartUp command 3Fh
Remark: This command can only be activated by a Power-On or Hard reset.
The StartUp command runs the reset and initialization phases. It does not need or return,
any data. It cannot be activated by the microprocessor but is automatically started after
one of the following events:
The reset phase comprises an asynchronous reset and configuration of certain register
bits. The initialization phase configures several registers with values stored in the
EEPROM.
When the StartUp command finishes, the Idle command is automatically executed.
Remark:
Table 131. Idle command 00h
The Idle command switches the MFRC531 to its inactive state where it waits for the next
command. It does not need or return, any data.
The device automatically enters the idle state when a command finishes. When this
happens, the MFRC531 sends an interrupt request by setting bit IdleIRq. When triggered
by the microprocessor, the Idle command can be used to stop execution of all other
commands (except the StartUp command) but this does not generate an interrupt request
(IdleIRq).
Remark: Stopping command execution with the Idle command does not clear the FIFO
buffer.
Command
StartUp
Command
Idle
•
•
•
•
•
•
Power-On Reset (POR) caused by power-up on pin DVDD
POR caused by power-up on pin AVDD
Negative edge on pin RSTPD
The microprocessor must not write to the MFRC531 while it is still executing the
StartUp command. To avoid this, the microprocessor polls for the Idle command to
determine when the initialization phase has finished; see
When the StartUp command is active, it is only possible to read from the Page 0
register.
The StartUp command cannot be interrupted by the microprocessor.
Value
3Fh
Value
00h
Rev. 3.4 — 26 January 2010
Action
runs the reset and initialization phase
Action
no action; cancels current command
execution
056634
Section 9.7.4 on page
Arguments
and data
-
Arguments
and data
-
ISO/IEC 14443 reader IC
MFRC531
© NXP B.V. 2010. All rights reserved.
Returned
data
-
Returned
data
-
75 of 116
28.