ATTINY26-16PI Atmel, ATTINY26-16PI Datasheet - Page 27

• Manufacturer Part Number: ATTINY26-16PI
• Description: IC AVR MCU 2K 16MHZ IND 20-DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY26-16PI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Low-frequency
Crystal Oscillator
1477K–AVR–08/10
The CKSEL0 Fuse together with the SUT1..0 Fuses select the start-up times as shown in Table
7.
Table 7. Start-up Times for the Crystal Oscillator Clock Selection
Notes:
To use a 32.768 kHz watch crystal as the clock source for the device, the Low-frequency Crystal
Oscillator must be selected by setting the PLLCK to “1” and CKSEL Fuses to “1001”. The crystal
should be connected as shown in Figure 22. By programming the CKOPT Fuse, the user can
enable internal capacitors on XTAL1 and XTAL2, thereby removing the need for external capac-
itors. The internal capacitors have a nominal value of 36 pF.
When this oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table 8.
Table 8. Start-up Times for the Low-frequency Crystal Oscillator Clock Selection
Note:
CKSEL0
SUT1..0
00
01
10
11
0
0
0
0
1
1
1
1
1. These options should only be used when not operating close to the maximum frequency of the
2. These options are intended for use with ceramic resonators and will ensure frequency stability
1. These options should only be used if frequency stability at start-up is not important for the
device, and only if frequency stability at start-up is not important for the application.
at start-up. They can also be used with crystals when not operating close to the maximum fre-
quency of the device, and if frequency stability at start-up is not important for the application.
application.
from Power-down
SUT1..0
Start-up Time
00
01
10
00
01
10
11
11
1K CK
1K CK
32K CK
(1)
(1)
from Power-down
Start-up Time
258 CK
258 CK
1K CK
1K CK
1K CK
16K CK
16K CK
16K CK
Additional Delay from
(2)
(2)
(2)
Reset (V
(1)
(1)
4.1 ms
65 ms
65 ms
CC
Additional Delay from
Reset (V
= 5.0V)
Reserved
4.1 ms
4.1 ms
4.1 ms
65 ms
65 ms
65 ms
–
CC
–
= 5.0V)
Fast rising power or BOD enabled
Recommended Usage
Slowly rising power
Stable frequency at start-up
Recommended
Usage
Ceramic resonator,
fast rising power
Ceramic resonator,
slowly rising power
Ceramic resonator,
BOD enabled
Ceramic resonator,
fast rising power
Ceramic resonator,
slowly rising power
Crystal Oscillator,
BOD enabled
Crystal Oscillator, fast
rising power
Crystal Oscillator,
slowly rising power
27