UPD70F3735GC-GAD-AX Renesas Electronics America, UPD70F3735GC-GAD-AX Datasheet - Page 679

• Manufacturer Part Number: UPD70F3735GC-GAD-AX
• Description: MCU 32BIT V850ES/JX3-L 80-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Lr

Specifications of UPD70F3735GC-GAD-AX

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 20MHz
• Connectivity: CSI, EBI/EMI, I²C, UART/USART
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 66
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Data Converters: A/D 8x10b, D/A 1x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

V850ES/JF3-L
21.5 IDLE2 Mode
21.5.1 Setting and operation status
normal operation mode.
on-chip peripheral functions stops.
The CPU, PLL, and other on-chip peripheral functions stop operating. However, the on-chip peripheral functions that can
operate with the subclock or an external clock continue operating.
on-chip peripheral functions, PLL, and flash memory. However, because the PLL and flash memory are stopped, a setup
time for the PLL and flash memory is required when IDLE2 mode is released.
21.5.2 Releasing IDLE2 mode
external interrupt request signal (INTP0 to INTP7 pin input), unmasked internal interrupt request signal from the peripheral
functions operable in the IDLE2 mode, or reset signal (reset by RESET pin input, WDT2RES signal, low-voltage detector
(LVI), or clock monitor (CLM)). The PLL returns to the operating status it was in before the IDLE2 mode was set.
R01UH0017EJ0400 Rev.4.00
Sep 30, 2010
The IDLE2 mode is set by setting the PSMR.PSM1 and PSMR.PSM0 bits to 10 and setting the PSC.STP bit to 1 in the
In the IDLE2 mode, the clock oscillator continues operation but clock supply to the CPU, PLL, flash memory, and other
As a result, program execution stops and the contents of the internal RAM before the IDLE2 mode was set are retained.
Table 21-7 shows the operating status in the IDLE2 mode.
The IDLE2 mode can reduce the power consumption more than the IDLE1 mode because it stops the operations of the
Cautions 1. Insert five or more NOP instructions after the instruction that stores data in the PSC register to
The IDLE2 mode is released by a non-maskable interrupt request signal (NMI pin input, INTWDT2 signal), unmasked
After the IDLE2 mode has been released, the normal operation mode is restored.
(1) Releasing IDLE2 mode by non-maskable interrupt request signal or unmasked maskable interrupt request
signal
The IDLE2 mode is released by a non-maskable interrupt request signal or an unmasked maskable interrupt
request signal, regardless of the priority of the interrupt request signal. If the IDLE2 mode is set in an interrupt
servicing routine, however, an interrupt request signal that is issued later is processed as follows.
Caution The interrupt request signal that is disabled by setting the PSC.NMI1M, PSC.NMI0M, and
(a) If an interrupt request signal with a priority lower than or equal to that of the interrupt request currently being
(b) If an interrupt request signal with a priority higher than that of the interrupt request currently being serviced is
serviced is issued, the IDLE2 mode is released, but that interrupt request signal is not acknowledged. The
interrupt request signal itself is retained.
issued (including a non-maskable interrupt request signal), the IDLE2 mode is released and that interrupt
request signal is acknowledged.
2. If the IDLE2 mode is set while an unmasked interrupt request signal is being held pending, the
set the IDLE2 mode.
IDLE2 mode is released immediately by the pending interrupt request.
PSC.INTM bits to 1 becomes invalid and IDLE2 mode is not released.
CHAPTER 21 STANDBY FUNCTION
Page 663 of 816