MC9S12XDP512CAG Freescale Semiconductor, MC9S12XDP512CAG Datasheet - Page 534

• Manufacturer Part Number: MC9S12XDP512CAG
• Description: IC MCU 512K FLASH 144-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12XDP512CAG

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, I²C, IrDA, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 119
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: S12XD
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 32 KB
• Interface Type: CAN/I2C/SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 119
• Number Of Timers: 12
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: EVB9S12XDP512E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (24-ch x 10-bit)
• Cpu Family: HCS12
• Device Core Size: 16b
• Frequency (max): 40MHz
• Total Internal Ram Size: 32KB
• # I/os (max): 119
• Number Of Timers - General Purpose: 12
• Operating Supply Voltage (typ): 2.5/5V
• Operating Supply Voltage (max): 2.75/5.5V
• Operating Supply Voltage (min): 2.35/3.15V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• For Use With: DEMO9S12XDT512E - BOARD DEMO FOR MC9S12XDT512EVB9S12XDP512E - BOARD DEMO FOR MC9S12XDP512
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 12 Serial Peripheral Interface (S12SPIV4)
The SS line can remain active low between successive transfers (can be tied low at all times). This format
is sometimes preferred in systems having a single fixed master and a single slave that drive the MISO data
line.
The SPI interrupt request flag (SPIF) is common to both the master and slave modes. SPIF gets set one
half SCK cycle after the last SCK edge.
534
•
End of Idle State
SCK Edge Number
SCK (CPOL = 0)
SCK (CPOL = 1)
SAMPLE I
MOSI/MISO
CHANGE O
CHANGE O
SEL SS (O)
Master only
SEL SS (I)
MOSI pin
MISO pin
Back-to-back transfers in master mode
In master mode, if a transmission has completed and a new data byte is available in the SPI data
register, this byte is sent out immediately without a trailing and minimum idle time.
MSB first (LSBFE = 0):
t
t
t
LSB first (LSBFE = 1):
L
T
I
= Minimum idling time between transfers (minimum SS high time), not required for back-to-back transfers
= Minimum leading time before the first SCK edge, not required for back-to-back transfers
= Minimum trailing time after the last SCK edge
t
L
1
MSB
LSB
2
Figure 12-12. SPI Clock Format 1 (CPHA = 1)
3
Begin
Bit 6
Bit 1
4
MC9S12XDP512 Data Sheet, Rev. 2.21
5
Bit 5
Bit 2
6
7
Bit 4
Bit 3
8
Transfer
9
Bit 3
Bit 4
10
11
Bit 2
Bit 5
12
13 14
Bit 1
Bit 6
End
15
MSB
LSB
16
t
T
Minimum 1/2 SCK
Freescale Semiconductor
Begin of Idle State
t
I
for t
T
t
L
, t
l
, t
L