ATMEGA32-16AU Atmel, ATMEGA32-16AU Datasheet - Page 31

• Manufacturer Part Number: ATMEGA32-16AU
• Description: IC AVR MCU 32K 16MHZ 5V 44TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32-16AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire/SPI/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Controller Family/series: AVR MEGA
• No. Of I/o's: 32
• Eeprom Memory Size: 1KB
• Ram Memory Size: 2KB
• Cpu Speed: 16MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 2KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: TQFP
• For Use With: ATSTK524 - KIT STARTER ATMEGA32M1/MEGA32C1ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATSTK600-TQFP44 - STK600 SOCKET/ADAPTER 44-TQFPATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

External Clock
Timer/Counter
Oscillator
2503Q–AVR–02/11
To drive the device from an external clock source, XTAL1 should be driven as shown in
14. To run the device on an external clock, the CKSEL fuses must be programmed to “0000”. By
programming the CKOPT Fuse, the user can enable an internal 36 pF capacitor between XTAL1
and GND.
Figure 14. External Clock Drive Configuration
When this clock source is selected, start-up times are determined by the SUT fuses as shown in
Table
Table 12. Start-up Times for the External Clock Selection
When applying an external clock, it is required to avoid sudden changes in the applied clock fre-
quency to ensure stable operation of the MCU. A variation in frequency of more than 2% from
one clock cycle to the next can lead to unpredictable behavior. It is required to ensure that the
MCU is kept in reset during such changes in the clock frequency.
For AVR microcontrollers with Timer/Counter Oscillator pins (TOSC1 and TOSC2), the crystal is
connected directly between the pins. No external capacitors are needed. The Oscillator is opti-
mized for use with a 32.768 kHz watch crystal. Applying an external clock source to TOSC1 is
not recommended.
Note:
SUT1..0
00
01
10
11
12.
The Timer/Counter Oscillator uses the same type of crystal oscillator as Low-Frequency Oscillator
and the internal capacitors have the same nominal value of 36 pF.
Start-up Time from
Power-down and
Power-save
6 CK
6 CK
6 CK
EXTERNAL
SIGNAL
CLOCK
Additional Delay
(V
from Reset
CC
Reserved
4.1ms
65ms
= 5.0V)
–
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
ATmega32(L)
Figure
31