ATMEGA16U4-AU Atmel, ATMEGA16U4-AU Datasheet - Page 421

• Manufacturer Part Number: ATMEGA16U4-AU
• Description: MCU AVR 16K FLASH USB 44TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16U4-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 26
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

35.5
7766F–AVR–11/10
ATmega16U4/ATmega32U4 Rev A
•
•
•
•
•
•
•
1. Spike on TWI pins when TWI is enabled
2. High current consumption in sleep mode
3. Increased power comsumption in power-down mode
4. Internal RC oscillator start up may fail
5. Internal RC oscillator calibration
6. Incorrect execution of VBUSTI interrupt
Spike on TWI pins when TWI is enabled
High current consumption in sleep mode
Increased power consumption in power-down mode
Internal RC oscillator start up may fail
Internal RC oscillator calibration
Incorrect execution of VBUSTI interrupt
Timer 4 enhanced mode issue
100 ns negative spike occurs on SDA and SCL pins when TWI is enabled.
Problem Fix/work around
Enable ATmega16U4/ATmega32U4 TWI before the other nodes of the TWI network.
If a pending interrupt cannot wake the part up from the selected mode, the current consump-
tion will increase during sleep when executing the SLEEP instruction directly after a SEI
instruction.
Problem Fix/work around
Before entering sleep, interrupts not used to wake up the part from the sleep mode should
be disabled.
The typical power consumption is increased by about 30 µA in power-down mode.
Problem Fix/work around
None.
When the part is configured to start on internal RC oscillator, the oscillator may not start
properly after power-on.
Problem Fix/work around
Do not configure the part to start on internal RC oscillator.
8 MHz frequency can be impossible to reach with internal RC even when using maximal
OSCAL value.
Problem Fix/work around
None.
The CPU may incorrectly execute the interrupt vector related to the VBUSTI interrupt flag.
Problem fix/work around
Do not enable this interrupt. Firmware must process this USB event by polling VBUSTI.
ATmega16/32U4
421