ATMEGA16U4-AU Atmel, ATMEGA16U4-AU Datasheet - Page 291

• Manufacturer Part Number: ATMEGA16U4-AU
• Description: MCU AVR 16K FLASH USB 44TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16U4-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 26
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

23.1
23.1.1
7766F–AVR–11/10
Analog Comparator Multiplexed Input
Digital Input Disable Register 1 – DIDR1
It is possible to select any of the ADC13..0 pins to replace the negative input to the Analog Com-
parator. The ADC multiplexer is used to select this input, and consequently, the ADC must be
switched off to utilize this feature. If the Analog Comparator Multiplexer Enable bit (ACME in
ADCSRB) is set and the ADC is switched off (ADEN in ADCSRA is zero), and MUX2..0 in
ADMUX select the input pin to replace the negative input to the Analog Comparator, as shown in
Table
input to the Analog Comparator.
Table 23-2.
• Bit 0 – AIN0D: AIN0 Digital Input Disable
When this bit is written logic one, the digital input buffer on the AIN0 pin is disabled. The corre-
sponding PIN Register bit will always read as zero when this bit is set. When an analog signal is
applied to the AIN0 pin and the digital input from this pin is not needed, this bit should be written
logic one to reduce power consumption in the digital input buffer.
Bit
Read/Write
Initial Value
ACME
0
1
1
1
1
1
1
1
1
1
23-2. If ACME is cleared or ADEN is set, the Bandgap reference is applied to the negative
ADEN
7
–
R
0
Analog Comparator Multiplexed Input
x
1
0
0
0
0
0
0
0
0
6
–
R
0
MUX2..0
000
001
010
011
100
101
110
111
xxx
xxx
5
–
R
0
Analog Comparator Negative Input
Bandgap Ref.
Bandgap Ref.
ADC0
ADC1
N/A
ADC4
ADC5
ADC6
ADC7
4
–
R
0
3
–
R
0
2
–
R
0
1
–
R
0
ATmega16/32U4
0
AIN0D
R/W
0
DIDR1
291