MC9S12NE64CPV Freescale Semiconductor, MC9S12NE64CPV Datasheet - Page 314

• Manufacturer Part Number: MC9S12NE64CPV
• Description: IC MCU 25MHZ ETHERNT/PHY 112LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12NE64CPV

• Mfg Application Notes: MC9S12NE64 Integrated Ethernet Controller Implementing an Ethernet Interface with the MC9S12NE64 Web Server Development with MC9S12NE64 and Open TCP
• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 3.465 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 16 bit
• Operating Supply Voltage: - 0.3 V to + 3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 65 C
• On-chip Adc: 10 bit
• For Use With: EVB9S12NE64E - BOARD EVAL FOR 9S12NE64DEMO9S12NE64E - DEMO BOARD FOR 9S12NE64
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

Chapter 11 Ethernet Media Access Controller (EMACV1)
MLB — MAC Loopback
FDX — Full Duplex
11.3.2.2 Receive Control and Status (RXCTS)
Read: Anytime.
Write: See each bit description.
314
While this bit is clear, the EMAC is configured for the internal PHY, all the EMAC MII I/O pins are
not available externally, and the MII interface to the internal PHY is available.
This bit can be written once after a hardware or software reset, but the user must not change this bit
while EMACE or BUSY is set.
While this bit is set, the EMAC is in the loopback mode which routes all transmit traffic to the receiver
and disables the MII.
This bit can be written anytime, but the user must not modify this bit while EMACE is set.
While this bit is set, the EMAC is set for full-duplex mode, which bypasses the carrier sense multiple
access with collision detect (CSMA/CD) protocol. Frame reception occurs independently of frame
transmission.
While this bit is clear, the EMAC is set for half-duplex mode. Frame reception is disabled during frame
transmission. The mode used is the traditional mode of operation that relies on the CSMA/CD protocol
to manage collisions and network access.
1 = External PHY.
0 = Internal PHY.
1 = Loopback mode.
0 = Normal operation.
1 = Full-duplex mode.
0 = Half-duplex mode.
Module Base + $3
RESET:
W
R
If MLB is set, EXTPHY is ignored. If EXTPHY is set, it is recommended
that any internal PHY be disabled.
While configured for loopback mode, receiver frame recognition algorithms
remain active and transmitted frames failing to meet acceptance criteria will
be dropped by the receiver.
RXACT
7
0
= Unimplemented or Reserved
Figure 11-3. Receive Control and Status (RXCTS)
6
0
0
MC9S12NE64 Data Sheet, Rev. 1.1
5
0
0
RFCE
NOTE
NOTE
4
0
3
0
0
PROM
2
0
CONMC
1
0
Freescale Semiconductor
BCREJ
0
0