MC9S12NE64CPV Freescale Semiconductor, MC9S12NE64CPV Datasheet - Page 178

• Manufacturer Part Number: MC9S12NE64CPV
• Description: IC MCU 25MHZ ETHERNT/PHY 112LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12NE64CPV

• Mfg Application Notes: MC9S12NE64 Integrated Ethernet Controller Implementing an Ethernet Interface with the MC9S12NE64 Web Server Development with MC9S12NE64 and Open TCP
• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 3.465 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 16 bit
• Operating Supply Voltage: - 0.3 V to + 3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 65 C
• On-chip Adc: 10 bit
• For Use With: EVB9S12NE64E - BOARD EVAL FOR 9S12NE64DEMO9S12NE64E - DEMO BOARD FOR 9S12NE64
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

Chapter 5 Oscillator (OSCV2)
5.2.1
These pins provide the operating voltage (V
allows the supply voltage to the OSCV2 to be independently bypassed.
5.2.2
These pins provide the interface for either a crystal or a CMOS compatible clock to control the internal
clock generator circuitry. EXTAL is the external clock input or the input to the crystal oscillator amplifier.
XTAL is the output of the crystal oscillator amplifier. All the MCU internal system clocks are derived from
the EXTAL input frequency. In full stop mode (PSTP = 0) the EXTAL pin is pulled down by an internal
resistor of typical 200 kΩ.
178
V
EXTAL and XTAL — Clock/Crystal Source Pins
DDPLL
Freescale Semiconductor recommends an evaluation of the application
board and chosen resonator or crystal by the resonator or crystal supplier
The Crystal circuit is changed from standard.
The Colpitts circuit is not suited for overtone resonators and crystals.
The Pierce circuit is not suited for overtone resonators and crystals without
a careful component selection.
and V
MCU
Figure 5-1. Colpitts Oscillator Connections (XCLKS = 0)
* Due to the nature of a translated ground Colpitts oscillator
EXTAL
a DC voltage bias is applied to the crystal.
Please contact the crystal manufacturer for crystal DC bias
conditions and recommended capacitor value CDC.
XTAL
SSPLL
MC9S12NE64 Data Sheet, Rev. 1.1
— PLL Operating Voltage, PLL Ground
CDC*
DDPLL
NOTE
NOTE
) and ground (V
C1
C2
V
SSPLL
Crystal or Ceramic
Resonator
SSPLL
) for the OSCV2 circuitry. This
Freescale Semiconductor
.