MC908JB8FBE Freescale Semiconductor, MC908JB8FBE Datasheet - Page 131

• Manufacturer Part Number: MC908JB8FBE
• Description: IC MCU 8K FLASH 3MHZ 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JB8FBE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 3MHz
• Connectivity: USB
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-QFP
• Processor Series: HC08JB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: USB
• Maximum Clock Frequency: 3 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 2
• Operating Supply Voltage: 5.25 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE, KITUSBSPIDGLEVME, KITUSBSPIEVME, KIT33810EKEVME
• Minimum Operating Temperature: 0 C
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 256Byte
• Cpu Speed: 8MHz
• No. Of Timers: 1
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Package: 44PQFP
• Family Name: HC08
• Maximum Speed: 3 MHz
• Cpu Family: HC08
• Device Core Size: 8b
• Frequency (max): 3MHz
• Total Internal Ram Size: 256Byte
• # I/os (max): 37
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4V
• Instruction Set Architecture: CISC
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

9.5.4 Resume After Suspend
9.5.4.1 Host Initiated Resume
9.5.4.2 USB Reset Signalling
9.5.4.3 Remote Wakeup
MC68HC908JB8•MC68HC08JB8•MC68HC08JT8 — Rev. 2.3
Freescale Semiconductor
The MCU can be activated from the suspend state by normal bus
activity, a USB reset signal, or by a forced resume driven from the MCU.
The host signals resume by initiating resume signalling (K state) for at
least 20ms followed by a standard low-speed EOP signal. This 20ms
ensures that all devices in the USB network are awakened.
After resuming the bus, the host must begin sending bus traffic within
37ms to prevent the device from re-entering suspend mode.
Reset can wake a device from the suspended mode.
The MCU also supports the remote wakeup feature. The firmware has
the ability to exit suspend mode by signaling a resume state to the
upstream host or hub. A non-idle state (K state) on the USB data lines is
accomplished by asserting the FRESUM bit in the UCR1 register.
When using the remote wakeup capability, the firmware must wait for at
least 5ms after the bus is in the idle state before sending the remote
wakeup resume signaling. This allows the upstream devices to get into
their suspend state and prepare for propagating resume signaling. The
FRESUM bit should be asserted to cause the resume state on the USB
data lines for at least 10ms, but not more than 15ms. Note that the
resume signalling is controlled by the FRESUM bit and meeting the
timing specifications is dependent on the firmware. When FRESUM is
cleared by firmware, the data lines will return to their high-impedance
state.
Refer to the register definitions (see
more information about how the force resume (FRESUM) bit can be
used to initiate the remote wakeup feature.
Universal Serial Bus Module (USB)
9.8.6 USB Control Register
Universal Serial Bus Module (USB)
Functional Description
Technical Data
1) for
131