AT32UC3L064 Atmel Corporation, AT32UC3L064 Datasheet - Page 809

• Manufacturer Part Number: AT32UC3L064
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L064

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

35.1.10
35.1.11
35.1.12
35.1.13
32099G–06/2011
ADCIFB
CAT
aWire
CHIP
Ensure that duty cycle writes from the user interface are not performed in a PWMA period
when an incoming peripheral event is expected.
Using STARTUPTIME larger than 0x1F will freeze the ADC
Writing a value larger than 0x1F to the Startup Time field in the ADC Configuration Register
(ACR.STARTUP) will freeze the ADC, and the Busy Status bit in the Status Register
(SR.BUSY) will never be cleared.
Fix/Workaround
Do not write values larger than 0x1F to ACR.STARTUP.
CAT asynchronous wake will be delayed by one AST event period
If the CAT detects a condition the should asynchronously wake the device in static mode,
the asynchronous wake will not occur until the next AST event. For example, if the AST is
generating events to the CAT every 50ms, and the CAT detects a touch at t=9200ms, the
asynchronous wake will occur at t=9250ms.
Fix/Workaround
None.
CAT QMatrix sense capacitors discharged prematurely
At the end of a QMatrix burst charging sequence that uses different burst count values for
different Y lines, the Y lines may be incorrectly grounded for up to n-1 periods of the periph-
eral bus clock, where n is the ratio of the PB clock frequency to the GCLK_CAT frequency.
This results in premature loss of charge from the sense capacitors and thus increased vari-
ability of the acquired count values.
Fix/Workaround
Enable the 1kOhm drive resistors on all implemented QMatrix Y lines (CSA 1, 3, 5, 7, 9, 11,
13, and/or 15) by writing ones to the corresponding odd bits of the CSARES register.
aWire CPU clock speed robustness
The aWire memory speed request command counter warps at clock speeds below approxi-
mately 5kHz.
Fix/Workaround
None.
The aWire debug interface is reset after leaving Shutdown mode
If the aWire debug mode is used as debug interface and the program enters Shutdown
mode, the aWire interface will be reset when the part receives a wakeup either from the
WAKE_N pin or the AST.
Fix/Workaround
None.
Increased Power Consumption in VDDIO in sleep modes
If OSC0 is enabled in crystal mode when entering a sleep mode where the OSC0 is dis-
abled, this will lead to an increased power consumption in VDDIO.
Fix/Workaround
AT32UC3L016/32/64
809