AT32UC3L064 Atmel Corporation, AT32UC3L064 Datasheet - Page 543

• Manufacturer Part Number: AT32UC3L064
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L064

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

24.6.1.4
24.6.1.5
32099G–06/2011
Clock control
TC operating modes
The clock of each counter can be controlled in two different ways: it can be enabled/disabled
and started/stopped. See
Figure 24-3. Clock Control
Each channel can independently operate in two different modes:
The TC operating mode selection is done by writing to the Wave bit in the CCRn register
(CCRn.WAVE).
In Capture mode, TIOA and TIOB are configured as inputs.
• The clock can be enabled or disabled by the user by writing to the Counter Clock
• The clock can also be started or stopped: a trigger (software, synchro, external or compare)
• Capture mode provides measurement on signals.
• Waveform mode provides wave generation.
Enable/Disable Command bits in the Channel n Clock Control Register (CCRn.CLKEN and
CCRn.CLKDIS). In Capture mode it can be disabled by an RB load event if the Counter Clock
Disable with RB Loading bit in CMRn is written to one (CMRn.LDBDIS). In Waveform mode,
it can be disabled by an RC Compare event if the Counter Clock Disable with RC Compare
bit in CMRn is written to one (CMRn.CPCDIS). When disabled, the start or the stop actions
have no effect: only a CLKEN command in CCRn can re-enable the clock. When the clock is
enabled, the Clock Enabling Status bit is set in SRn (SRn.CLKSTA).
always starts the clock. In Capture mode the clock can be stopped by an RB load event if the
Counter Clock Stopped with RB Loading bit in CMRn is written to one (CMRn.LDBSTOP). In
Waveform mode it can be stopped by an RC compare event if the Counter Clock Stopped
with RC Compare bit in CMRn is written to one (CMRn.CPCSTOP). The start and the stop
commands have effect only if the clock is enabled.
Selected
Clock
Counter
Clock
Q
Figure 24-3 on page
S
R
Trigger
543.
CLKSTA
Q
AT32UC3L016/32/64
CLKEN
S
R
Event
Stop
CLKDIS
Disable
Event
543