AT32UC3L064 Atmel Corporation, AT32UC3L064 Datasheet - Page 188

• Manufacturer Part Number: AT32UC3L064
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L064

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

13.5.3.1
13.5.3.2
32099G–06/2011
Enabling the DFLL
Internal synchronization
The DFLL can operate in both open loop mode and closed-loop mode. In closed-loop mode a
low frequency clock with high accuracy can be used as reference clock to get high accuracy on
the output clock (CLK_DFLL).
To prevent unexpected writes due to software bugs, write access to the configuration registers is
protected by a locking mechanism. For details please refer to the UNLOCK register description.
Figure 13-1. DFLLIF Block Diagram
The DFLL is enabled by writing a one to the Enable bit (EN) in the DFLLn Configuration Register
(DFLLnCONF). No other bits or fields in DFLLnCONF must be changed simultaneously, or
before the DFLL is enabled.
Due to multiple clock domains in the DFLLIF, values in the DFLLIF configuration registers need
to be synchronized to other clock domains. The status of this synchronization can be read from
the Power and Clocks Status Register (PCLKSR). Before writing to a DFLLIF configuration reg-
ister, the user must check that the DFLLn Synchronization Ready bit (DFLLnRDY) in PCLKSR is
set. When this bit is set, the DFLL can be configured, and CLK_DFLL is ready to be used. Any
write to a DFLLIF configuration register while DFLLnRDY is cleared will be ignored.
• Internal oscillator with no external components
• 40-150 MHz frequency in closed-loop mode
• Can operate standalone as a high-frequency programmable oscillator in open loop mode
• Can operate as an accurate frequency multiplier against a known frequency in closed-loop
• Optional spread-spectrum clock generation
• Very high-frequency multiplication supported - can generate all frequencies from a 32 KHz
mode
clock
8+9
32
CSIZE
FSIZE
FMUL
IMUL
DFLLLOCKLOSTC
DFLLLOCKC
FREQUENCY
DFLLLOCKLOSTF
TUNER
DFLLLOCKF
COARSE
FINE
DFLLLOCKLOSTA
DFLLLOCKA
8
9
DFLL
AT32UC3L016/32/64
CLK_DFLLIF_DITHER
CLK_DFLLIF_REF
188