AT32UC3L064 Atmel Corporation, AT32UC3L064 Datasheet - Page 796

• Manufacturer Part Number: AT32UC3L064
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L064

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32.10.5
Table 32-42. TWI-Bus Timing Requirements
32099G–06/2011
t
t
t
t
t
t
r
f
HD-STA
SU-STA
SU-STO
HD-DAT
Symbol
TWIM/TWIS Timing
TWCK and TWD rise time
TWCK and TWD fall time
(Repeated) START hold time
(Repeated) START set-up time
STOP set-up time
Data hold time
Parameter
The maximum SPI slave input frequency is given by the following formula:
Where
CPOL and NCPHA.
ter for a description of this clock.
Maximum SPI Frequency, Slave Output Mode
The maximum SPI slave output frequency is given by the following formula:
Where
SPI master setup time. Please refer to the SPI master datasheet for
imum frequency of the SPI pins. Please refer to the I/O Pin Characteristics section for the
maximum frequency of the pins.
Figure 32-42
them. Some of these requirements (t
vention. Compliance with the other requirements (t
TWI
TWIM and TWIS user interface registers. Please refer to the TWIM and TWIS sections for more
information.
, t
HIGH
SPIn
SPIn
, and f
Standard
Fast
Standard
Fast
Standard
Fast
Standard
Fast
Standard
Fast
Standard
Fast
shows the TWI-bus timing requirements and the compliance of the device with
is the MISO delay, SPI6 or SPI9 depending on CPOL and NCPHA.
is the MOSI setup and hold time, SPI7 + SPI8 or SPI10 + SPI11 depending on
TWCK
Mode
(1)
) requires user intervention through appropriate programming of the relevant
f
CLKSPI
(1)
Requirement
f
SPCKMAX
is the maximum frequency of the CLK_SPI. Refer to the SPI chap-
0.3
0.6
4.7
0.6
4.0
0.6
f
4
SPCKMAX
(2)
20 + 0.1C
20 + 0.1C
Minimum
r
=
and t
MIN f
-
-
=
f
) are met by the device without requiring user inter-
b
b
(
MIN f
Device
PINMAX
4t
2t
t
t
clkpb
clkpb
clkpb
clkpb
(
HD-STA
CLKSPI
,
------------------------------------
SPIn
, t
AT32UC3L016/32/64
,
SU-STA
----------- -
SPIn
Requirement
+
1
1
t
SETUP
3.45
)
0.9
, t
SU-STO
()
()
)
Maximum
t
SETUP
1000
, t
300
300
300
-
-
-
HD-DAT
15t
.
f
prescaled
PINMAX
Device
, t
SU-DAT-TWI
t
SETUP
+ t
is the max-
clkpb
, t
is the
Unit
LOW-
μ s
μ s
μs
μs
796
ns
ns