AT32UC3L064 Atmel Corporation, AT32UC3L064 Datasheet - Page 314

• Manufacturer Part Number: AT32UC3L064
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L064

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

17.5.1.1
17.5.2
17.5.3
32099G–06/2011
Measurement
Interrupts
Cautionary note
Note that if clock selected as source for CLK_REF is stopped during a measurement, this will
not be detected by the FREQM. The BUSY bit in the STATUS register will never be cleared, and
the DONE interrupt will never be triggered. If the clock selected as soruce for CLK_REF is
stopped, it will not be possible to change the source for the reference clock as long as the
selected source is not running.
In the Mode Register the Clock Source Selection (CLKSEL) field selects CLK_MSR and the
Number of Reference Clock Cycles (REFNUM) field selects the duration of the measurement.
The duration is given in number of CLK_REF periodes.
Writing a one to the START bit in the Control Register (CTRL) starts the measurement. The
BUSY bit in SR is cleared when the measurement is done.
The result of the measurement can be read from the Value Register (VALUE). The frequency of
the measured clock CLK_MSR is then:
The FREQM has two interrupt sources:
These will generate an interrupt request if the corresponding bit in the Interrupt Mask Register
(IMR) is set. The interrupt sources are ORed together to form one interrupt request. The FREQM
will generate an interrupt request if at least one of the bits in the Interrupt Mask Register (IMR) is
set. Bits in IMR are set by writing a one to the corresponding bit in the Interrupt Enable Register
(IER) and cleared by writing a one to this bit in the Interrupt Disable Register (IDR). The interrupt
request remains active until the corresponding bit in the Interrupt Status Register (ISR) is
cleared by writing a one to this bit in the Interrupt Clear Register (ICR). Because all the interrupt
sources are ORed together, the interrupt request from the FREQM will remain active until all the
bits in ISR are cleared.
• Write a zero to the MODE.REFCEN to disable he clock, without changing the other bits/fields
• Wait until the SR.RCLKBUSY bit reads as zero.
• DONE: A frequency measurement is done
• RCLKRDY: The reference clock is ready
in the Mode register.
f
CLK_MSR
= (VALUE/REFNUM)*f
CLK_REF
AT32UC3L016/32/64
314