71M6543F-IGT/F Maxim Integrated Products, 71M6543F-IGT/F Datasheet - Page 108

• Manufacturer Part Number: 71M6543F-IGT/F
• Description: PMIC Solutions Precision Energy Meter IC
• Manufacturer: Maxim Integrated Products
• Type: Metering SoCr

Specifications of 71M6543F-IGT/F

• Core: 8051
• Core Architecture: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 5 KB
• Device Million Instructions Per Second: 5 MIPS
• Interface Type: I2C, ICE, SPI, UART
• Maximum Clock Frequency: 5 MHz
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Number Of Programmable I/os: 51
• Number Of Timers: 2
• On-chip Adc: 22 bit
• Operating Supply Voltage: 3 V to 3.6 V
• Package / Case: LQFP-100
• Processor Series: 8051
• Program Memory Size: 64 KB
• Program Memory Type: Flash
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

71M6543F/H and 71M6543G/GH Data Sheet
108
Name
FL_BANK[1:0]
FLSH_ERASE[7:0]
FLSH_MEEN
FLSH_PEND
FLSH_PGADR[5:0]
FLSH_PSTWR
SFR B6[1:0] 01 01 R/W
SFR B7[7:2] 0
SFR 94[7:0] 0
SFR B2[1]
SFR B2[3]
SFR B2[2]
Location Rst Wk Dir
0
0
0
0
0
0
0
0
© 2008–2011 Teridian Semiconductor Corporation
R/W
W
W
W
R
Description
Flash Bank Selection (71M6543G and 71M6543GH only)
The program memory of the 71M6543G/GH consists of a fixed lower bank of 32 KB,
addressable at 0x0000 to 0x7FFF plus an upper banked area of 32 KB, addressable at
0x8000 to 0xFFFF. The I/O RAM register FL_BANK is used to switch one of four
memory banks of 32 KB each into the address range from 0x8000 to 0xFFFF. Note that
when FL_BANK = 0, the upper bank is the same as the lower bank.
Flash Erase Initiate
FLSH_ERASE is used to initiate either the Flash Mass Erase cycle or the Flash Page
Erase cycle. Specific patterns are expected for FLSH_ERASE in order to initiate the
appropriate Erase cycle. (default = 0x00).
0x55 – Initiate Flash Page Erase cycle. Must be proceeded by a write to
0xAA – Initiate Flash Mass Erase cycle. Must be proceeded by a write to
Any other pattern written to FLSH_ERASE has no effect.
Mass Erase Enable
0 = Mass Erase disabled (default).
1 = Mass Erase enabled.
Must be re-written for each new Mass Erase cycle.
Indicates that a posted flash write is pending. If another flash write is attempted, it is
ignored.
Flash Page Erase Address
Flash Page Address (page 0 thru 63) that is erased during the Page Erase cycle.
(default = 0x00).
Must be re-written for each new Page Erase cycle.
Enables posted flash writes. When 1, and if CE_E = 1, flash write requests are stored in
a one element deep FIFO and are executed when CE_BUSY falls. FLSH_PEND can be
read to determine the status of the FIFO. If FLSH_PSTWR = 0 or if CE_E = 0, flash writes
are immediate.
FL_BANK[1:0]
00
01
10
11
FLSH_PGADR[5:0] (SFR 0xB7).
FLSH_MEEN (SFR 0xB2) and the debug (CC) port must be enabled.
Address Range for Lower Bank
(0x0000-0x7FFF)
0x0000-0x7FFF
0x0000-0x7FFF
0x0000-0x7FFF
0x0000-0x7FFF
Address Range for Upper Bank
0x18000-0x1FFFF
0x10000-0x17FFF
(0x8000-0xFFFF)
0x0000-0x7FFF
0x8000-0xFFFF
v1.2