ADSP-21364BSWZ-1AA Analog Devices Inc, ADSP-21364BSWZ-1AA Datasheet - Page 45

• Manufacturer Part Number: ADSP-21364BSWZ-1AA
• Description: IC DSP 32BIT 333MHZ EPAD 144LQFP
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Fixed/Floating Pointr

Specifications of ADSP-21364BSWZ-1AA

• Interface: DAI, SPI
• Clock Rate: 333MHz
• Non-volatile Memory: ROM (512 kB)
• On-chip Ram: 384kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.20V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 144-LQFP Exposed Pad, 144-eLQFP, 144-HLQFP
• Frequency: 333MHz
• Supply Voltage: 1.2V
• Embedded Interface Type: Serial, SPI
• Supply Voltage Range: 1.14V To 1.26V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case: RoHS Compliant
• No. Of Bits: 32 / 40
• Rohs Compliant: Yes
• Package: 144LQFP EP
• Numeric And Arithmetic Format: Floating-Point
• Maximum Speed: 333 MHz
• Ram Size: 384 KB
• Device Million Instructions Per Second: 333 MIPS
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

THERMAL CHARACTERISTICS
The processor is rated for performance over the temperature
range specified in Operating Conditions
Table 42
JEDEC standards JESD51-2 and JESD51-6 and the junction-to-
board measurement complies with JESD51-8. Test board and
thermal via design comply with JEDEC standards JESD51-9
(BGA) and JESD51-5 (LQFP_EP). The junction-to-case mea-
surement complies with MIL-STD-883. All measurements use a
2S2P JEDEC test board.
Industrial applications using the BGA package require thermal
vias, to an embedded ground plane, in the PCB. Refer to JEDEC
standard JESD51-9 for printed circuit board thermal ball land
and thermal via design information.
Industrial applications using the LQFP_EP package require
thermal trace squares and thermal vias, to an embedded ground
plane, in the PCB. Refer to JEDEC standard JESD51-5 for more
information.
To determine the junction temperature of the device while on
the application PCB, use:
where:
T
T
package
Ψ
is the typical value from
P
ADSP-21362 SHARC Processors (EE-277) for more information.
Values of θ
design considerations.
D
J
T
JT
= junction temperature (
= case temperature (
= power dissipation. See Estimating Power for the
= junction-to-top (of package) characterization parameter
Figure 42. Typical Output Delay or Hold versus Load Capacitance
- 2
- 4
10
8
6
4
2
0
through
0
JA
are provided for package comparison and PCB
y = 0.0488x - 1.5923
Table 44
T
(at Ambient Temperature)
J
50
°
=
C) measured at the top center of the
Table 42
T
airflow measurements comply with
ADSP-21362/ADSP-21363/ADSP-21364/ADSP-21365/ADSP-21366
°
C)
T
LOAD CAPACITANCE (pF)
+
through
100
JT
P
on Page
D
Table
150
44.
14.
Rev. G | Page 45 of 56 | March 2011
200
Values of θ
design considerations when an exposed pad is required. Note
that the thermal characteristics values provided in
through
Table 42. Thermal Characteristics for BGA (No Thermal vias
in PCB)
Table 43. Thermal Characteristics for BGA (Thermal vias in
PCB)
Table 44. Thermal Characteristics for LQFP_EP (with
Exposed Pad Soldered to PCB)
Parameter
θ
θ
θ
θ
Ψ
Ψ
Ψ
Parameter
θ
θ
θ
θ
Ψ
Ψ
Ψ
Parameter
θ
θ
θ
θ
Ψ
Ψ
Ψ
JA
JMA
JMA
JC
JA
JMA
JMA
JC
JA
JMA
JMA
JC
JT
JMT
JMT
JT
JMT
JMT
JT
JMT
JMT
Table 44
JC
are provided for package comparison and PCB
Condition
Airflow = 0 m/s
Airflow = 1 m/s
Airflow = 2 m/s
Airflow = 0 m/s
Airflow = 1 m/s
Airflow = 2 m/s
Condition
Airflow = 0 m/s
Airflow = 1 m/s
Airflow = 2 m/s
Airflow = 0 m/s
Airflow = 1 m/s
Airflow = 2 m/s
Condition
Airflow = 0 m/s
Airflow = 1 m/s
Airflow = 2 m/s
Airflow = 0 m/s
Airflow = 1 m/s
Airflow = 2 m/s
are modeled values.
Typical
25.40
21.90
20.90
5.07
0.140
0.330
0.410
Typical
23.40
20.00
19.20
5.00
0.130
0.300
0.360
Typical
16.80
14.20
13.50
7.25
0.51
0.72
0.80
Table 42
Unit
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
Unit
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
Unit
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W