71M6534-IGT/F Maxim Integrated Products, 71M6534-IGT/F Datasheet - Page 29

• Manufacturer Part Number: 71M6534-IGT/F
• Description: IC ENERY METER 3PH 128K 120-LQFP
• Manufacturer: Maxim Integrated Products

Specifications of 71M6534-IGT/F

• Mounting Style: SMD/SMT
• Package / Case: LQFP-120
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1.4.7 Timers and Counters
The 80515 has two 16-bit timer/counter registers: Timer 0 and Timer 1. These registers can be configured
for counter or timer operations.
In timer mode, the register is incremented every 12 MPU clock cycles. In counter mode, the register is
incremented when the falling edge is observed at the corresponding input signal T0 or T1 (T0 and T1 are
the timer gating inputs derived from certain DIO pins, see
cycles to recognize a 1-to-0 event, the maximum input count rate is 1/2 of the clock frequency (CKMPU).
There are no restrictions on the duty cycle, however to ensure proper recognition of the 0 or 1 state, an
input should be stable for at least 1 machine cycle.
Four operating modes can be selected for Timer 0 and Timer 1, as shown in
TMOD Register, shown in
is controlled by the TCON Register, which is shown in
Table 23.
set.
Table 21
Rev 2
Bit
Timer/Counter 1:
TMOD[7]
TMOD[6]
M1
0
0
1
1
In Mode 3, TL0 is affected by TR0 and gate control bits, and sets the TF0 flag on overflow, while
TH0 is affected by the TR1 bit, and the TF1 flag is set on overflow.
specifies the combinations of operation modes allowed for Timer 0 and Timer 1.
Bits TR1 (TCON[6]) and TR0 (TCON[4]) in the TCON register start their associated timers when
M0
0
1
0
1
Symbol
Gate
C/T
Timer 0 - mode 0
Timer 0 - mode 1
Timer 0 - mode 2
Mode 0
Mode 1
Mode 2
Mode 3
Table 21: Allowed Timer/Counter Mode Combinations
Mode
Table 22: TMOD Register Bit Description (SFR 0x89)
Table
Table 20: Timers/Counters Mode Description
Function
If TMOD[7] is set, external input signal control is enabled for Counter 0.
external gate control. The TR1 bit in the TCON register (SFR 0x88) must
also be set in order for Counter 1 to increment.
With these settings Counter 1 is incremented on every falling edge of the
logic signal applied to one or more of the interrupt sources controlled by
the DI_RBP, DIO_R1, … DIO_RXX registers.
Selects timer or counter operation. When set to 1, a counter operation is
performed. When cleared to 0, the corresponding register will function as a
22, is used to select the appropriate mode. The timer/counter operation
Function
13-bit Counter/Timer mode with 5 lower bits in the TL0 or TL1 register
and the remaining 8 bits in the TH0 or TH1 register (for Timer 0 and
Timer 1, respectively). The 3 high order bits of TL0 and TL1 are held
at zero.
16-bit Counter/Timer mode.
8-bit auto-reload Counter/Timer. The reload value is kept in TH0 or
TH1, while TL0 or TL1 is incremented every machine cycle. When
TL(x) overflows, a value from TH(x) is copied to TL(x) (where x is 0
for counter/timer 0 or 1 for counter/timer 1.
If Timer 1 M1 and M0 bits are set to 1, Timer 1 stops.
If Timer 0 M1 and M0 bits are set to 1, Timer 0 acts as two independent
8-bit Timer/Counters.
Not allowed
Mode 0
Yes
Yes
Section 1.5.7
Not allowed
Timer 1
Mode 1
Yes
Yes
Digital
I/O). Since it takes 2 machine
Table 20
Mode 2
Yes
Yes
Yes
and
Table
21. The
29