MCF5214CVF66 Freescale Semiconductor, MCF5214CVF66 Datasheet - Page 133

• Manufacturer Part Number: MCF5214CVF66
• Description: IC MPU 32BIT COLDF 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF521xr

Specifications of MCF5214CVF66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 142
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Package: 256MA-BGA
• Device Core: ColdFire
• Family Name: MCF521x
• Maximum Speed: 66 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 142
• Interface Type: QSPI/UART/I2C/CAN
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 8
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

6.4.3.4
The ACCERR flag will be set during a command write sequence if any of the illegal operations below are
performed. Such operations will cause the command sequence to immediately abort.
The PVIOL flag will be set during a command write sequence after the longword write to the CFM array
if any of the illegal operations below are performed. Such operations will cause the command sequence to
immediately abort.
If a Flash physical block is read during a program or erase operation on that block (CFMUSTAT bit CCIF
= 0), the read will return non-valid data and the ACCERR flag will not be set.
6.4.4
If a command is active (CCIF = 0) when the MCU enters stop mode, the command sequence monitor
performs the following:
Freescale Semiconductor
1. Writing to the CFM array before initializing CFMCLKD.
2. Writing to the CFM array while in emulation mode.
3. Writing a byte or a word to the CFM array. Only 32-bit longword programming is allowed.
4. Writing to the CFM array while CBEIF is not set.
5. Writing an invalid user command to the CFMCMD.
6. Writing to any CFM other than CFMCMD after writing a longword to the CFM array.
7. Writing a second command to CFMCMD before executing the previously written command.
8. Writing to any CFM register other than CFMUSTAT (to clear CBEIF) after writing to the
9. Entering stop mode while a program or erase command is in progress.
10. Aborting a command sequence by writing a 0 to CBEIF after the longword write to the CFM
1. Writing to an address in a protected area of the CFM array.
2. Writing a mass erase command to CFMCMD while any logical sector is protected (see
1. The command in progress aborts
2. The Flash high voltage circuitry switches off and any pending command (CBEIF = 0) does not
3. The CCIF and ACCERR flags are set if a command is active when the MCU enters stop mode.
command register.
array or after writing a command to CFMCMD and before launching it.
Section 6.3.4.4, “CFM Protection Register
executed when the MCU exits stop mode.
Stop Mode
Flash User Mode Illegal Operations
The state of any longword(s) being programmed or any erase pages/physical
blocks being erased is not guaranteed if the MCU enters stop mode with a
command in progress.
Active commands are immediately aborted when the MCU enters stop
mode. Do not execute the STOP instruction during program and erase
operations.
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
WARNING
NOTE
(CFMPROT)”).
ColdFire Flash Module (CFM)
6-21