PIC18F96J65-I/PT Microchip Technology, PIC18F96J65-I/PT Datasheet - Page 292

• Manufacturer Part Number: PIC18F96J65-I/PT
• Description: IC PIC MCU FLASH 48KX16 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F96J65-I/PT

• Core Size: 8-Bit
• Program Memory Size: 96KB (48K x 16)
• Core Processor: PIC
• Speed: 41.667MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Type: FLASH
• Ram Size: 3808 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 70
• Ram Memory Size: 3.71875KB
• Cpu Speed: 41.667MHz
• No. Of Timers: 5
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3808 B
• Interface Type: Display Driver, Ethernet, EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 41.667 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 5
• Operating Supply Voltage: 2.35 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183033, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162064 - HEADER INTFC MPLABICD2 64/80/100AC164323 - MODULE SKT FOR 100TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F97J60 FAMILY
19.4.8
To initiate a Start condition, the user sets the Start
Enable bit, SEN (SSPxCON2<0>). If the SDAx and
SCLx pins are sampled high, the Baud Rate Generator
is reloaded with the contents of SSPxADD<6:0> and
starts its count. If SCLx and SDAx are both sampled
high when the Baud Rate Generator times out (T
the SDAx pin is driven low. The action of the SDAx
being driven low while SCLx is high is the Start condi-
tion and causes the S bit (SSPxSTAT<3>) to be set.
Following this, the Baud Rate Generator is reloaded
with the contents of SSPxADD<6:0> and resumes its
count. When the Baud Rate Generator times out
(T
matically cleared by hardware. The Baud Rate
Generator is suspended, leaving the SDAx line held
low and the Start condition is complete.
FIGURE 19-21:
DS39762E-page 292
BRG
), the SEN bit (SSPxCON2<0>) will be auto-
I
CONDITION TIMING
2
C MASTER MODE START
Write to SEN bit occurs here
FIRST START BIT TIMING
SDAx
SCLx
SDAx = 1,
SCLx = 1
T
BRG
BRG
),
Set S bit (SSPxSTAT<3>)
T
S
BRG
At completion of Start bit,
hardware clears SEN bit
19.4.8.1
If the user writes the SSPxBUF when a Start sequence
is in progress, the WCOL is set and the contents of the
buffer are unchanged (the write doesn’t occur).
and sets SSPxIF bit
Note:
Note:
Write to SSPxBUF occurs here
T
BRG
If, at the beginning of the Start condition,
the SDAx and SCLx pins are already sam-
pled low, or if during the Start condition, the
SCLx line is sampled low before the SDAx
line is driven low, a bus collision occurs.
The Bus Collision Interrupt Flag, BCLxIF,
is set, the Start condition is aborted and
the I
Because queueing of events is not
allowed, writing to the lower 5 bits of
SSPxCON2 is disabled until the Start
condition is complete.
1st bit
WCOL Status Flag
T
2
BRG
C module is reset into its Idle state.
© 2009 Microchip Technology Inc.
2nd bit