MCP6V01DM-VOS Microchip Technology, MCP6V01DM-VOS Datasheet - Page 29

• Manufacturer Part Number: MCP6V01DM-VOS
• Description: DEMO BOARD FOR MCP6V01
• Manufacturer: Microchip Technology

Specifications of MCP6V01DM-VOS

• Channels Per Ic: 1 - Single
• Amplifier Type: Chopper (Zero-Drift)
• Output Type: Rail-to-Rail
• Slew Rate: 0.5 V/µs
• Current - Output / Channel: 22mA
• Operating Temperature: -40°C ~ 125°C
• Voltage - Supply, Single/dual (±): 1.8 V ~ 5.5 V
• Board Type: Fully Populated
• Utilized Ic / Part: MCP6V01
• Silicon Manufacturer: Microchip
• Application Sub Type: Operational Amplifier
• Kit Application Type: Amplifier
• Silicon Core Number: MCP6V01, MCP6V03, MCP6V06, MCP6V08
• Kit Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Current - Supply (main Ic): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.4
4.4.1
Many sensors are configured as Wheatstone bridges.
Strain gauges and pressure sensors are two common
examples. These signals can be small and the
common mode noise large. Amplifier designs with high
differential gain are desirable.
Figure 4-15
bridge with a minimum of components. Because the
circuit is not symmetric, the ADC input is single ended,
and there is a minimum of filtering, the CMRR is good
enough for moderate common mode noise.
FIGURE 4-15:
Figure 4-16
Wheatstone bridges. This circuit is symmetric and has
high CMRR. Using a differential input to the ADC helps
with the CMRR.
FIGURE 4-16:
© 2008 Microchip Technology Inc.
R R
R R
R R
R R
V
Typical Applications
DD
WHEATSTONE BRIDGE
shows how to interface to a Wheatstone
shows a higher performance circuit for
10 nF
10 nF
V
DD
0.2R
0.2R
Simple Design.
High Performance Design.
1 µF
200Ω
200Ω
200 Ω
200 Ω
0.01C
100R
MCP6V01
20 kΩ
20 kΩ
3 kΩ
1 µF
1 µF
3 kΩ
3 kΩ
½ MCP6V02
½ MCP6V02
ADC
V
DD
ADC
V
DD
4.4.2
The ratiometric circuit in
wire RTD. It corrects for the sensor’s wiring resistance
by subtracting the voltage across the middle R
top R1 does not change the output voltage; it balances
the op amp inputs. Failure (open) of the RTD is
detected by an out of range voltage.
FIGURE 4-17:
The voltages at the input of the ADC can be calculated
with the following:
Where:
R
R
R
V
V
R
100Ω
W
W
W
V
V
CM
DM
V
G
RTD
W
V
V
B
T
RTD
G
DM
CM
W
RTD SENSOR
=
=
=
=
=
=
=
=
=
10 nF
10 nF
1
G
G
V
------------------------------------------------------------------------------
V
T
+
RTD
RTD
DD
+
MCP6V01/2/3
2 R
Voltage at the top of R
Voltage at the bottom of R
Voltage across top and middle
R
ADC’s common mode input
ADC’s differential mode input
R
20 kΩ
R
20 kΩ
V
⋅
(
W
–
T
B
V
RTD Sensor.
B
’s
1 µF
R
2.49 kΩ
2.49 kΩ
T
3
Figure 4-17
+
2.49 kΩ
2.49 kΩ
3
–
⁄
(
R
R
R
⁄
V
G
R
2
1
1
B
1
RTD
)
2
+
G
+
W
R
2.55 kΩ
R
2.55 kΩ
1 G
100 kΩ
100 kΩ
100 nF
100 nF
DS22058C-page 29
conditions a three
V
2
2
–
R
R
W
3
3
½ MCP6V02
½ MCP6V02
W
)V
RTD
W
RTD
3 kΩ
3 kΩ
ADC
W
V
. The
DD