NCP5331FTR2G ON Semiconductor, NCP5331FTR2G Datasheet - Page 30

• Manufacturer Part Number: NCP5331FTR2G
• Description: IC CTLR PWM 2PH W/DRVRS 32-LQFP
• Manufacturer: ON Semiconductor

Specifications of NCP5331FTR2G

• Applications: Controller, AMD Athlon™
• Voltage - Input: 9 ~ 14 V
• Number Of Outputs: 2
• Voltage - Output: 5V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 32-LQFP
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: NCP5331FTR2G; NCP5331FTR2GOSTR

NOTE:
NOTE:
NOTE:
Figure 39. COMP Tuning, Bandwidth Too High
Figure 38. COMP Tuning, Bandwidth Too Low
Figure 40. COMP Tuning, Bandwidth Optimal
The value of C
bandwidth too low. COMP slews too slowly which
results in overshoot in V
The value of C
bandwidth too high. COMP moves too quickly, which is
evident from the small spike in its voltage when the
load is applied or removed. The output voltage
transitions more slowly because of the COMP spike.
The value of C
without spiking or ringing. V
and monotonically settles to its final value.
A1
A1
A1
is too high and the loop gain/
is too low and the loop gain/
is optimal. COMP slews quickly
CORE
CORE
.
does not overshoot
http://onsemi.com
NCP5331
30
8. Error Amplifier Tuning
current sense network has been optimized the Error
Amplifier must be tuned. Basically, the gain of the Error
Amplifier should be adjusted to provide an acceptable
transient response by increasing or decreasing the Error
Amplifier’s feedback capacitor (C
Diagram). The bandwidth of the control loop will vary
directly with the gain of the error amplifier.
COMP pin will slew too slowly, and the output voltage will
overshoot as shown in Figure 38. On the other hand, if C
is too small the loop gain/bandwidth will be high, the COMP
pin will slew very quickly and overshoot. Integrator “wind
up” is the cause of the overshoot. In this case the output
voltage will transition more slowly because COMP spikes
upward as shown in Figure 39. Too much loop
gain/bandwidth increase the risk of instability. In general,
one should use the lowest loop gain/bandwidth as possible
to achieve acceptable transient response − this will insure
good stability. If C
quickly but not overshoot and the output voltage will
monotonically settle as shown in Figure 40.
transient response the steady−state voltage ripple on the COMP
pin should be examined. When the converter is operating at
full, steady−state load, the peak−to−peak voltage ripple on
the COMP pin should be less than 20 mVpp as shown in
Figure 41. Less than 10 mVpp is ideal. Excessive ripple on
the COMP pin will contribute to output voltage jitter.
9. Current Limit Setting
CO2 in the block diagram) exceeds the voltage on the I
pin the part will enter hiccup mode. For inductive sensing,
the I
maximum resistance (R
NOTE:
After the steady−state (static) AVP has been set and the
If C
After the control loop is tuned to provide an acceptable
When the output of the current sense amplifier (CO1 or
LIM
Figure 41. COMP Ripple for a Stable System
A1
is too large the loop gain/bandwidth will be low, the
pin voltage should be set based on the inductor’s
At full load the peak−to−peak voltage ripple on the
COMP pin should be less than 20 mV for a
well−tuned/stable controller. Higher COMP voltage
ripple will contribute to output voltage jitter.
A1
is optimal the COMP pin will slew
LMAX
). The design must consider
A1
in the Applications
LIM
A1