W9751G6KB WINBOND [Winbond], W9751G6KB Datasheet - Page 16

no-image

W9751G6KB

Manufacturer Part Number
W9751G6KB
Description
8M ? 4 BANKS ? 16 BIT DDR2 SDRAM
Manufacturer
WINBOND [Winbond]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
W9751G6KB-18
Manufacturer:
WINBOND
Quantity:
7 600
Part Number:
W9751G6KB-18
Manufacturer:
Winbond
Quantity:
9 680
Company:
Part Number:
W9751G6KB-18
Quantity:
245
Company:
Part Number:
W9751G6KB-18
Quantity:
20 000
Part Number:
W9751G6KB-25
Manufacturer:
ISSI
Quantity:
3 140
Part Number:
W9751G6KB-25
Manufacturer:
Winbond Electronics
Quantity:
10 000
Part Number:
W9751G6KB-25
Manufacturer:
WINBOND/华邦
Quantity:
20 000
Company:
Part Number:
W9751G6KB-25
Quantity:
98
Company:
Part Number:
W9751G6KB-25
Quantity:
20
Company:
Part Number:
W9751G6KB-25
Quantity:
203
7.2.3.1
OCD impedance adjustment can be done using the following EMRS mode. In drive mode all outputs
are driven out by DDR2 SDRAM. In Drive (1) mode, all DQ, DQS signals are driven HIGH and all
signals are driven HIGH. In adjust mode, BL = 4 of operation code data must be used. In case of OCD
calibration default, output driver characteristics have a nominal impedance value of 18 Ohms during
nominal temperature and voltage conditions. OCD applies only to normal full strength output drive
setting defined by EMR (1) and if reduced strength is set, OCD default driver characteristics are not
applicable. When OCD calibration adjust mode is used, OCD default output driver characteristics are
not applicable. After OCD calibration is completed or driver strength is set to default, subsequent
EMRS commands not intended to adjust OCD characteristics must specify A[9:7] as ‟000‟ in order to
maintain the default or calibrated value.
7.2.3.2
To adjust output driver impedance, controllers must issue the ADJUST EMRS command along with a
4 bit burst code to DDR2 SDRAM as in table 2. For this operation, Burst Length has to be set to BL =
4 via MRS command before activating OCD and controllers must drive the burst code to all DQs at the
same time. D
output impedance is adjusted for all DDR2 SDRAM DQs simultaneously and after OCD calibration, all
DQs and DQS‟s of a given DDR2 SDRAM will be adjusted to the same driver strength setting. The
maximum step count for adjustment is 16 and when the limit is reached, further increment or
decrement code has no effect. The default setting may be any step within the 16 step range. When
Adjust mode command is issued, AL from previously set value must be applied.
DQS signals are driven LOW. In Drive (0) mode, all DQ, DQS signals are driven LOW and all DQS
D
4 bit burst code inputs to all DQs
0
0
0
0
1
0
0
1
1
T0
A9
0
0
0
1
1
Extended Mode Register for OCD Impedance Adjustment
OCD Impedance Adjust
Other Combinations
D
T0
0
0
0
1
0
1
1
0
0
T1
in table 2 means all DQ bits at bit time 0, D
A8
0
0
1
0
1
D
0
0
1
0
0
0
1
0
1
T2
A7
0
1
0
0
1
Table 2 – OCD Adjust Mode Program
Table 1 – OCD Drive Mode Program
D
0
1
0
0
0
1
0
1
0
T3
Operation
OCD calibration mode exit
Drive (1) DQ, DQS HIGH and DQS LOW
Drive (0) DQ, DQS LOW and DQS HIGH
Adjust mode
OCD calibration default
NOP (No operation)
Increase by 1 step
Decrease by 1 step
NOP
NOP
Increase by 1 step
Decrease by 1 step
Increase by 1 step
Decrease by 1 step
Pull-up driver strength
- 16 -
T1
at bit time 1, and so forth. The driver
Publication Release Date: Dec. 09, 2011
Operation
Reserved
NOP (No operation)
NOP
NOP
Increase by 1 step
Decrease by 1 step
Increase by 1 step
Increase by 1 step
Decrease by 1 step
Decrease by 1 step
Pull-down driver strength
W9751G6KB
Revision A01

Related parts for W9751G6KB