PEB20534H-10 SIEMENS [Siemens Semiconductor Group], PEB20534H-10 Datasheet - Page 121
![no-image](/images/no-image-200.jpg)
PEB20534H-10
Manufacturer Part Number
PEB20534H-10
Description
DMA Supported Serial Communication Controller with 4 Channels DSCC4
Manufacturer
SIEMENS [Siemens Semiconductor Group]
Datasheet
1.PEB20534H-10.pdf
(442 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PEB20534H-10-V2.1
Manufacturer:
INF
Quantity:
5 510
Company:
Part Number:
PEB20534H-10-V2.1
Manufacturer:
PHILIPS
Quantity:
5 510
Company:
Part Number:
PEB20534H-10V2.1
Manufacturer:
MICRON
Quantity:
78
- Current page: 121 of 442
- Download datasheet (2Mb)
After performing all necessary initializations of the SSC, the serial interfaces can be
enabled. For a master device, the alternate clock line will now go to its programmed
polarity. The alternate data line will go to either ’0’ or ’1’, until the first transfer will start.
After a transfer the alternate data line will always remain at the logic level of the last
transmitted data bit.
When the serial interface is enabled, the master device can initiate the first data transfer
by writing the transmit data into register SSCTB. This value is copied into the shift
register (which is assumed to be empty at this time), and the selected first bit of the
transmit data will be placed onto the MTSR line on the next clock from the baudrate
generator (transmission only starts, if SSCEN=’1’). Depending on the selected clock
phase, a clock pulse will also be generated on the MSCLK line. With the opposite clock
edge the master at the same time latches and shifts in the data detected at its input line
MRST. This ’exchanges’ the transmit data with the receive data. Since the clock line is
connected to all slaves, their shift registers will be shifted synchronously with the
master's shift register, shifting out the data contained in the registers, and shifting in the
data detected at the input line. After the preprogrammed number of clock pulses (via the
data width selection) the data transmitted by the master is contained in all slaves’ shift
registers, while the master's shift register holds the data of the selected slave. In the
master and all slaves the content of the shift register is copied into the receive buffer
SSCRB and the receive interrupt flag SSCRXI is set.
A slave device will immediately output the selected first bit (MSB or LSB of the transfer
data) at pin MRST, when the content of the transmit buffer is copied into the slave's shift
register. It will not wait for the next clock from the baudrate generator, as the master
does. The reason is that, depending on the selected clock phase, the first clock edge
generated by the master may already be used to clock in the first data bit. Hence the
slave's first data bit must already be valid at this time.
Note: On the SSC always a transmission and a reception takes place at the same time,
The initialization of the MSCLK pin on the master requires some attention in order to
avoid undesired clock transitions, which may disturb the other receivers. The state of the
internal alternate output lines is '1' as long as the SSC is disabled. This alternate output
signal is ANDed with the respective port line output latch. Enabling the SSC with an idle-
low clock (SSCPO=’0’) will drive the alternate data output and (via the AND) the port pin
MSCLK immediately low. To avoid this, use the following sequence:
• select the clock idle level (SSCPO=’x’),
• load the port output latch with the desired clock idle level (GPDATA.p=’x’),
• switch the pin to output (GPDIR.p=’1’),
• enable the SSC (SSCEN=’1’), and
• if SSCPO=’0’: enable alternate data output (GPDATA.p=’1’).
Semiconductor Group
regardless whether valid data has been transmitted or received. This is different,
e.g., from asynchronous reception on ASC0.
121
Multi Function Port (MFP)
Data Sheet 09.98
PEB 20534
Related parts for PEB20534H-10
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![S80C32-12](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Intel 80C32 - Siemens SAB-C501, Nearest Equivalent Replacement
Manufacturer:
Siemens Semiconductor Group
![BAT14-033](/images/no-image3.png)
Part Number:
Description:
HiRel Silicon Schottky Diode (HiRel Discrete and Microwave Semiconductor Medium barrier diodes for detector and mixer applications)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![BXY43-P1](/images/no-image3.png)
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![BXY44-T1](/images/no-image3.png)
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![IRL80](/images/no-image3.png)
Part Number:
Description:
GaAs-Infrarot-Sendediode GaAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![IRL81](/images/no-image3.png)
Part Number:
Description:
GaAlAs-Infrarot-Sendediode GaAlAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![BSM50GB100D](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
IGBT MODULE
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BSM181R](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BSM254F](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
(BSMxxx) TRANSISTOR
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BSM111AR](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BUZ48](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
main ratings
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![TDA4716C](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![DL440M](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![SDA5255](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet: