AD9992_07 AD [Analog Devices], AD9992_07 Datasheet - Page 55
AD9992_07
Manufacturer Part Number
AD9992_07
Description
12-Bit CCD Signal Processor with Precision Timing Generator
Manufacturer
AD [Analog Devices]
Datasheet
1.AD9992_07.pdf
(92 pages)
- Current page: 55 of 92
- Download datasheet (2Mb)
GP LOOK-UP TABLES (LUT)
The AD9992 is equipped with a look-up table for each pair of
consecutive GP signals when configured as outputs. GP1 is
always combined with GP2, GP3 is always combined with GP4,
GP5 is always combined with GP6, and GP7 is always combined
with GP8. The external GPO outputs from each pair can output
the result of the LUT or the original GP internal signal.
Address 0x79 dictates the behavior of the LUT and which
signals receive the result. Each 4-bit LUT_FOR_GPxy register
can realize any logic combination of GPx and GPy. For example,
Table 24 shows how the register values of LUT_FOR_GP12 [11:8]
are determined. XOR, NAND, AND, and OR results are shown,
but any 4-bit combination is possible. A simple example of XOR
gating is shown in Figure 64.
GP1
GP2
Figure 63. Internal LUT for GP1 and GP2 Signals
LUT
GP2_USE_LUT
GP1_USE_LUT
0
1
0
1
GPO1
GPO2
Rev. C | Page 55 of 92
Table 24. LUT Results Based on GP1 and GP2 Values
GP2
0
0
1
1
Field Counter and GPO Limitations
The following is a summary of the known limitations of the field
counters and GPO signals that dictate usability:
• The field counter trigger (PRIMARY_ACTION and
• If GP*_PROTOCOL = 1, it must be manually reset to
SECONDARY_ACTION registers, Address 0x70) is self-reset
at the start of every VD period. Therefore, there must be one
VD period between sequential programming to that address.
GP*_PROTOCOL = 0 one VD period before it can be used
again. If manual toggles are desired in sequential fields, the
MANUAL_TRIG register should be used in conjunction with
GP*_PROTOCOL = 1.
GPO2
GPO1
GP1
GP2
GP1
0
1
0
1
NOTES
1. LOGIC COMBINATION (XOR) OF PROGRAMMED TOGGLES
GP1 AND GP2.
Figure 64. LUT Example for GP1 XOR GP2
LUT: XOR
0
1
1
0
GP2_USE_LUT = 1
LUT_FOR_GP12[11:8] = 0x06
LUT: NAND
1
1
1
0
GP1_USE_LUT = 0
LUT: AND
0
0
0
1
AD9992
LUT: OR
0
1
1
1
Related parts for AD9992_07
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DPG2 EVAL ADAPTER FOR XILINX BOARDS
Manufacturer:
Analog Devices Inc
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
RF Development Tools Sransceiver board for FMC evaluation kit
Manufacturer:
Analog Devices
Part Number:
Description:
Analog Devices: Data Converters: DAC 12-Bit, 10 ns to 100 ns Converters Selection Table
Manufacturer:
AD [Analog Devices]
Datasheet:
Part Number:
Description:
Analog Devices: Data Converters: DAC 8-Bit, 10 ns to 100 ns Converters Selection Table
Manufacturer:
AD [Analog Devices]
Datasheet:
Part Number:
Description:
Low-Power Analog Front End with DSP Microcomputer
Manufacturer:
AD [Analog Devices]
Datasheet:
Part Number:
Description:
2 Pair/1 Pair ETSI Compatible HDSL Analog Front End
Manufacturer:
AD [Analog Devices]
Datasheet: