EPC16xxx Altera, EPC16xxx Datasheet - Page 11

no-image

EPC16xxx

Manufacturer Part Number
EPC16xxx
Description
(EPC4 / EPC8 / EPC16) Enhanced Configuration Devices
Manufacturer
Altera
Datasheet
Figure 2–3. Concurrent Configuration of Multiple FPGAs in PS Mode (n = 8)
Notes to
(1)
(2)
(3)
(4)
(5)
(6)
Altera Corporation
August 2005
Connect V
The nINIT_CONF pin is available on enhanced configuration devices and has an internal pull-up resistor that is
always active. This means an external pull-up resistor is not required on the nINIT_CONF/nCONFIG line. The
nINIT_CONF pin does not need to be connected if its functionality is not used. If nINIT_CONF is not used, nCONFIG
must be pulled to V
The enhanced configuration devices’ OE and nCS pins have internal programmable pull-up resistors. If internal
pull-up resistors are used, external pull-up resistors should not be used on these pins. The internal pull-up resistors
are used by default in the Quartus II software. To turn off the internal pull-up resistors, check the Disable nCS and
OE pull-ups on configuration device option when generating programming files.
For PORSEL, PGM[], and EXCLK pin connections, refer to
In the 100-pin PQFP package, you must externally connect the following pins: C-A0 to F-A0, C-A1 to F-A1, C-A15
to F-A15, C-A16 to F-A16, and BYTE# to V
100-pin PQFP and 88-pin Ultra FineLine BGA packages: C-RP# to F-RP#, C-WE# to F-WE#, TM1 to V
GND, and WP# to V
Connect the FPGA MSEL[] input pins to select the PS configuration mode. For details, refer to the appropriate
FPGA family chapter in the Configuration Handbook.
(6)
(6)
(6)
Figure
N.C.
N.C.
N.C.
n
n
n
CC
2–3:
to the same supply voltage as the configuration device.
MSEL
nCEO
MSEL
nCEO
MSEL
nCEO
CC
CC
.
either directly or through a resistor.
FPGA1
FPGA7
FPGA0
CONF_DONE
CONF_DONE
CONF_DONE
nCONFIG
nCONFIG
nCONFIG
nSTATUS
nSTATUS
nSTATUS
DATA0
DATA0
DATA0
DCLK
DCLK
DCLK
nCE
nCE
nCE
Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet
GND
GND
GND
V
CC
CC
. Additionally, you must make the following pin connections in both
(3)
(1)
V
CC
(3)
(1)
Table
2–9.
GND
V
(1)
CC
Enhanced Configuration
BYTE# (5)
WP#
TM1
DATA 7
C-A0 (5)
C-A1 (5)
C-A15 (5)
C-A16 (5)
WE#C
RP#C
DCLK
DATA0
DATA1
OE
nCS
nINIT_CONF (2)
TMO
(3)
(3)
Configuration Handbook, Volume 2
Device
PGM[2..0]
DQ[15..0]
PORSEL
A[20..0]
RY/BY#
EXCLK
VCCW
WE#F
A0-F
A1-F
A15-F
A16-F
RP#F
OE#
CE#
V
CC
(4)
(4)
(4)
(1)
CC
N.C.
N.C.
N.C.
N.C.
N.C.
, TM0 to
2–11

Related parts for EPC16xxx