ST72325R6-AUTO STMicroelectronics, ST72325R6-AUTO Datasheet - Page 115
ST72325R6-AUTO
Manufacturer Part Number
ST72325R6-AUTO
Description
8-bit Mcu For Automotive With 16 To 60 Kbyte Flash, Adc, Css, 5 Timers, Spi, Sci, I2c Interface
Manufacturer
STMicroelectronics
Datasheet
1.ST72325R6-AUTO.pdf
(250 pages)
- Current page: 115 of 250
- Download datasheet (5Mb)
ST72325xxx-Auto
Note:
13.3.5
1
2
3
4
5
If the timer clock is an external clock, the formula is:
Where:
Clearing the output compare interrupt request (that is, clearing the OCFi bit) is done by:
1.
2.
The following procedure is recommended to prevent the OCFi bit from being set between
the time it is read and the write to the OC
●
●
●
After a processor write cycle to the OCiHR register, the output compare function is inhibited
until the OCiLR register is also written.
If the OCiE bit is not set, the OCMPi pin is a general I/O port and the OLVLi bit will not
appear when a match is found but an interrupt could be generated if the OCIE bit is set.
In both internal and external clock modes, OCFi and OCMPi are set while the counter value
equals the OCiR register value (see
Figure 52 on page 116
PWM mode.
The output compare functions can be used both for generating external events on the
OCMPi pins even if the input capture mode is also used.
The value in the 16-bit OC
successful comparison in order to control an output waveform or establish a new elapsed
timeout.
Forced compare output capability
When the FOLVi bit is set by software, the OLVLi bit is copied to the OCMPi pin. The OLVi bit
has to be toggled in order to toggle the OCMPi pin when it is enabled (OCiE bit = 1). The
OCFi bit is then not set by hardware, and thus no interrupt request is generated.
The FOLVLi bits have no effect in both one pulse mode and PWM mode.
∆t
f
Reading the SR register while the OCFi bit is set
An access (read or write) to the OCiLR register
Write to the OCiHR register (further compares are inhibited).
Read the SR register (first step of the clearance of the OCFi bit, which may be already
set).
Write to the OCiLR register (enables the output compare function and clears the OCFi
bit).
CPU
= Output compare period (in seconds)
= External timer clock frequency (in hertz)
for an example with f
i
R register and the OLVi bit should be changed after each
Figure 51 on page 116
∆ OCiR = ∆t
i
R register:
CPU
/4). This behavior is the same in OPM or
*
f
EXT
for an example with f
16-bit timer
CPU
115/250
/2 and
Related parts for ST72325R6-AUTO
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: