SAM9RL64 Atmel Corporation, SAM9RL64 Datasheet - Page 156
SAM9RL64
Manufacturer Part Number
SAM9RL64
Description
Manufacturer
Atmel Corporation
Datasheets
1.M40800.pdf
(284 pages)
2.SAM9260.pdf
(290 pages)
3.SAM9261.pdf
(248 pages)
4.SAM9R64.pdf
(903 pages)
5.SAM9R64.pdf
(52 pages)
Specifications of SAM9RL64
Flash (kbytes)
0 Kbytes
Pin Count
217
Max. Operating Frequency
240 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
118
Ext Interrupts
118
Usb Transceiver
1
Usb Speed
Hi-Speed
Usb Interface
Device
Spi
1
Twi (i2c)
2
Uart
5
Ssc
2
Sd / Emmc
1
Graphic Lcd
Yes
Video Decoder
No
Camera Interface
No
Adc Channels
6
Adc Resolution (bits)
10
Adc Speed (ksps)
220
Resistive Touch Screen
Yes
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
64
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.08 to 1.32
Fpu
No
Mpu / Mmu
No / Yes
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- M40800 PDF datasheet
- SAM9260 PDF datasheet #2
- SAM9261 PDF datasheet #3
- SAM9R64 PDF datasheet #4
- SAM9R64 PDF datasheet #5
- Current page: 156 of 290
- Download datasheet (5Mb)
Debug Interface and EmbeddedICE-RT
7.8.3
7-18
Comms channel monitor mode debug status register
You can use the following instructions to access these registers:
MRC p14, 0, Rd, c0, c0
This returns the debug comms control register into Rd.
MCR p14, 0, Rn, c1, c0
This writes the value in Rn to the comms data write register.
MRC p14, 0, Rd, c1, c0
This returns the debug data read register into Rd.
The Thumb instruction set does not support coprocessor instructions. Therefore, the
processor must be in ARM state before you can access the debug comms channel.
The coprocessor 14 monitor mode debug status register is provided for use by a debug
monitor when the ARM9E-S is configured into the monitor mode debug mode.
The coprocessor 14 monitor mode debug status register is a 1-bit wide read/write
register having the format shown in Figure 7-9.
Bit 0 of the register, the DbgAbt bit, indicates whether the processor took a Prefetch or
Data Abort in the past because of a breakpoint or watchpoint. If the ARM9E-S core
takes a Prefetch Abort as a result of a breakpoint or watchpoint, then the bit is set. If on
a particular instruction or data fetch, both the debug abort and external abort signals are
asserted, the external abort takes priority and the DbgAbt bit is not set. You can read or
write the DbgAbt bit using
Note
Copyright © 2000 ARM Limited. All rights reserved.
Figure 7-9 Coprocessor 14 monitor mode debug status register format
MRC
or
MCR
instructions.
ARM DDI 0165B
Related parts for SAM9RL64
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: