SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 843

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

39.7.8.8
Figure 39-42. Slave Node Synchronization
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
Fractional Part (FP)
Fractional Part (FP)
Clcok Divider (CD)
Clcok Divider (CD)
Synchro Counter
US_LINBRR
US_LINBRR
US_BRGR
US_BRGR
LINIDRX
Clock
RXD
Slave Node Synchronization
The synchronization is done only in Slave node configuration. The procedure is based on time
measurement between falling edges of the Synch Field. The falling edges are available in dis-
tances of 2, 4, 6 and 8 bit times.
Figure 39-41. Synch Field
The time measurement is made by a 19-bit counter clocked by the sampling clock (see
39.7.1).
When the start bit of the Synch Field is detected, the counter is reset. Then during the next
8 Tbits of the Synch Field, the counter is incremented. At the end of these 8 Tbits, the counter is
stopped. At this moment, the 16 most significant bits of the counter (value divided by 8) give the
new clock divider (LINCD) and the 3 least significant bits of this value (the remainder) give the
new fractional part (LINFP).
When the Synch Field has been received, the clock divider (CD) and the fractional part (FP) are
updated in the Baud Rate Generator register (US_BRGR).
If it appears that the sampled Synch character is not equal to 0x55, then the error flag LINISFE
in the Channel Status register (US_CSR) is set to 1. It is reset by writing bit RSTSTA to 1 in the
Control register (US_CR).
The accuracy of the synchronization depends on several parameters:
• The nominal clock frequency (F
13 dominant bits (at 0)
Break Field
Initial CD
Initial CD
Initial FP
Initial FP
Start
bit
2 Tbit
1 recessive bit
Delimiter
Break
(at 1)
Reset
Start
Bit
Nom
2 Tbit
1
) (the theoretical slave node clock frequency)
0
8 Tbit
Synch Byte = 0x55
1
Synch Field
0
2 Tbit
1
0
1
0
000_0011_0001_0110_1101
2 Tbit
Stop
Bit
0000_0110_0010_1101
101
Start
Bit
ID0 ID1 ID2 ID3 ID4 ID5 ID6 ID7
Stop
bit
SAM9G35
SAM9G35
Stop
Bit
Section
843
843