SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 738

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

738
738
SAM9G35
SAM9G35
• the waveform duty cycle. This channel parameter is defined in the CDTY field of the
• the waveform polarity. At the beginning of the period, the signal can be at high or low level.
• the waveform alignment. The output waveform can be left or center aligned. Center aligned
source clock and can be calculated:
By using the Master Clock (MCK) divided by an X given prescaler value
(with X being 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, or 1024), the resulting period formula
will be:
By using a Master Clock divided by one of both DIVA or DIVB divider, the formula becomes,
respectively:
If the waveform is center aligned then the output waveform period depends on the counter
source clock and can be calculated:
By using the Master Clock (MCK) divided by an X given prescaler value
(with X being 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, or 1024). The resulting period formula will
be:
By using a Master Clock divided by one of both DIVA or DIVB divider, the formula becomes,
respectively:
PWM_CDTYx register.
If the waveform is left aligned then:
If the waveform is center aligned, then:
This property is defined in the CPOL field of the PWM_CMRx register. By default the signal
starts by a low level.
waveforms can be used to generate non overlapped waveforms. This property is defined in
the CALG field of the PWM_CMRx register. The default mode is left aligned.
--------------------------------------------- -
--------------------------------------------------- -
------------------------------ -
---------------------------------------- -
X*CPRD*DIVA
2*X*CPRD*DIVA
X CPRD
2 X CPRD
duty cycle
duty cycle
MCK
MCK
MCK
MCK
=
=
------------------------------------------------------------------------------------------------------- -
---------------------------------------------------------------------------------------------------------------------- -
period 1 fchannel_x_clock
or
period 2
or
--------------------------------------------- -
X*CPRD*DIVB
--------------------------------------------------- -
2*X*CPRD*DIVB
–
MCK
MCK
–
1 fchannel_x_clock
period
period 2
CDTY
CDTY
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11