ATtiny461 Automotive Atmel Corporation, ATtiny461 Automotive Datasheet - Page 121

• Manufacturer Part Number: ATtiny461 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATtiny461 Automotive

• Flash (kbytes): 4 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.25
• Eeprom (bytes): 256
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 150
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

16.11.4
7753F–AVR–01/11
TCCR1D – Timer/Counter1 Control Register D
Table 16-18. Compare Output Mode, Phase and Frequency Correct PWM Mode
• Bit 1 - FOC1D: Force Output Compare Match 1D
The FOC1D bit is only active when the PWM1D bit specify a non-PWM mode.
Writing a logical one to this bit forces a change in the Waveform Output (OCW1D) and the Out-
put Compare pin (OC1D) according to the values already set in COM1D1 and COM1D0. If
COM1D1 and COM1D0 written in the same cycle as FOC1D, the new settings will be used. The
Force Output Compare bit can be used to change the output pin value regardless of the timer
value. The automatic action programmed in COM1D1 and COM1D0 takes place as if a compare
match had occurred, but no interrupt is generated. The FOC1D bit is always read as zero.
• Bit 0 - PWM1D: Pulse Width Modulator D Enable
When set (one) this bit enables PWM mode based on comparator OCR1D.
• Bit 7 - FPIE1: Fault Protection Interrupt Enable
Setting this bit (to one) enables the Fault Protection Interrupt.
• Bit 6– FPEN1: Fault Protection Mode Enable
Setting this bit (to one) activates the Fault Protection Mode.
• Bit 5 – FPNC1: Fault Protection Noise Canceler
Setting this bit activates the Fault Protection Noise Canceler. When the noise canceler is acti-
vated, the input from the Fault Protection Pin (INT0) is filtered. The filter function requires four
successive equal valued samples of the INT0 pin for changing its output. The Fault Protection is
therefore delayed by four Oscillator cycles when the noise canceler is enabled.
• Bit 4 – FPES1: Fault Protection Edge Select
This bit selects which edge on the Fault Protection pin (INT0) is used to trigger a fault event.
When the FPES1 bit is written to zero, a falling (negative) edge is used as trigger, and when the
FPES1 bit is written to one, a rising (positive) edge will trigger the fault.
Bit
0x26 (0x46)
Read/Write
Initial value
COM1D1..0
00
01
10
11
OCW1D Behavior
Normal port operation.
Cleared on Compare Match when up-counting.
Set on Compare Match when down-counting.
Cleared on Compare Match when up-counting.
Set on Compare Match when down-counting.
Set on Compare Match when up-counting.
Cleared on Compare Match when down-counting.
FPIE1
R/W
7
0
FPEN1
R/W
6
0
FPNC1
R/W
ATtiny261/ATtiny461/ATtiny861
5
0
FPES1
R/W
4
0
FPAC1
R/W
3
0
FPF1
R/W
0
2
Disconnected
Connected
Connected
Connected
OC1D Pin
WGM11
R/W
1
0
WGM10
R/W
0
0
Disconnected
Disconnected
Disconnected
Connected
OC1D Pin
TCCR1D
121