ATmega162 Atmel Corporation, ATmega162 Datasheet - Page 58

• Manufacturer Part Number: ATmega162
• Manufacturer: Atmel Corporation

Specifications of ATmega162

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 35
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 6
• Input Capture Channels: 2
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

58
ATmega162/V
Notes:
Table 25. Reset and Interrupt Vectors if M161C is programmed
Notes:
Vector No.
10
11
12
13
14
15
16
17
18
19
20
21
22
1
2
3
4
5
6
7
8
9
1. When the BOOTRST Fuse is programmed, the device will jump to the Boot Loader address at
2. When the IVSEL bit in GICR is set, Interrupt Vectors will be moved to the start of the Boot
1. When the BOOTRST Fuse is programmed, the device will jump to the Boot Loader address at
2. When the IVSEL bit in GICR is set, Interrupt Vectors will be moved to the start of the Boot
reset, see
Flash section. The address of each Interrupt Vector will then be the address in this table added
to the start address of the Boot Flash section.
reset, see
Flash section. The address of each Interrupt Vector will then be the address in this table added
to the start address of the Boot Flash section.
Address
Program
0x000
0x00C
0x01C
0x002
0x004
0x006
0x008
0x00A
0x00E
0x010
0x012
0x014
0x016
0x018
0x01A
0x01E
0x020
0x022
0x024
0x026
0x028
0x02A
“Boot Loader Support – Read-While-Write Self-programming” on page
“Boot Loader Support – Read-While-Write Self-programming” on page
(1)
(2)
Source
RESET
INT0
INT1
INT2
TIMER2 COMP
TIMER2 OVF
TIMER1 CAPT
TIMER1 COMPA
TIMER1 COMPB
TIMER1 OVF
TIMER0 COMP
TIMER0 OVF
SPI, STC
USART0, RXC
USART1, RXC
USART0, UDRE
USART1, UDRE
USART0, TXC
USART1, TXC
EE_RDY
ANA_COMP
SPM_RDY
Reset, Watchdog Reset, and JTAG AVR
Reset
External Interrupt Request 0
External Interrupt Request 1
External Interrupt Request 2
Timer/Counter2 Compare Match
Timer/Counter1 Capture Event
Timer/Counter1 Compare Match A
Timer/Counter1 Compare Match B
Timer/Counter1 Overflow
Timer/Counter0 Compare Match
Timer/Counter0 Overflow
USART0, Tx Complete
USART1, Tx Complete
Analog Comparator
Store Program Memory Ready
Interrupt Definition
External Pin, Power-on Reset, Brown-out
Timer/Counter2 Overflow
Serial Transfer Complete
USART0, Rx Complete
USART1, Rx Complete
USART0 Data Register Empty
USART1 Data Register Empty
EEPROM Ready
2513K–AVR–07/09
217.
217.