SC16IS741IPW,128 NXP Semiconductors, SC16IS741IPW,128 Datasheet - Page 5

no-image

SC16IS741IPW,128

Manufacturer Part Number
SC16IS741IPW,128
Description
IC UART 16TSSOP
Manufacturer
NXP Semiconductors
Type
IrDA or RS-232 or RS-485r
Datasheets

Specifications of SC16IS741IPW,128

Number Of Channels
1, UART
Package / Case
16-TSSOP (0.173", 4.40mm Width)
Features
RS-485
Fifo's
64 Byte
Protocol
RS232, RS485
Voltage - Supply
2.5V, 3.3V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
Mounting Type
Surface Mount
Data Rate
5 Mbps
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.3 V
Supply Current
6 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Operating Supply Voltage
2.5 V, 3.3 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
935290736128
NXP Semiconductors
7. Functional description
SC16IS741_1
Product data sheet
Table 2.
[1]
The UART will perform serial-to-I
peripheral devices or modems, and I
transmitted by the host. The complete status the SC16IS741 UART can be read at any
time during functional operation by the host.
The SC16IS741 can be placed in an alternate mode (FIFO mode) relieving the host of
excessive software overhead by buffering received/transmitted characters. Both the
receiver and transmitter FIFOs can store up to 64 characters (including three additional
bits of error status per character for the receiver FIFO) and have selectable or
programmable trigger levels.
The SC16IS741 has selectable hardware flow control and software flow control. Hardware
flow control significantly reduces software overhead and increases system efficiency by
automatically controlling serial data flow using the RTS output and CTS input signals.
Software flow control automatically controls data flow by using programmable Xon/Xoff
characters.
The UART includes a programmable baud rate generator that can divide the timing
reference clock input by a divisor between 1 and (2
Symbol
V
RTS
CTS
TX
RX
RESET
XTAL1
XTAL2
SS
See
Section 7.4 “Hardware reset, Power-On Reset (POR) and software reset”
Pin description
Pin
9
10
11
12
13
14
15
16
Type Description
-
O
I
O
I
I
I
O
Single UART with I
Rev. 01 — 29 April 2010
…continued
ground
UART request to send (active LOW). A logic 0 on the RTS pin
indicates the transmitter has data ready and waiting to send. Writing a
logic 1 in the modem control register MCR[1] will set this pin to a
logic 0, indicating data is available. After a reset this pin is set to a
logic 1. This pin only affects the transmit and receive operations when
auto RTS function is enabled via the Enhanced Feature Register
(EFR[6]) for hardware flow control operation.
UART clear to send (active LOW). A logic 0 (LOW) on the CTS pin
indicates the modem or data set is ready to accept transmit data from
the SC16IS741. Status can be tested by reading MSR[4]. This pin
only affects the transmit and receive operations when auto CTS
function is enabled via the Enhanced Feature Register EFR[7] for
hardware flow control operation.
UART transmitter output. During the local Loopback mode, the TX
output pin is disabled and TX data is internally connected to the
UART RX input.
UART receiver input. During the local Loopback mode, the RX input
pin is disabled and TX data is connected to the UART RX input
internally.
device hardware reset (active LOW)
Crystal input or external clock input. Functions as a crystal input or as
an external clock input. A crystal can be connected between XTAL1
and XTAL2 to form an internal oscillator circuit (see
Alternatively, an external clock can be connected to this pin.
Crystal output or clock output. (See also XTAL1.) XTAL2 is used as a
crystal oscillator output.
2
C conversion on data characters received from
2
C-to-serial conversion on data characters
2
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
16
– 1).
[1]
SC16IS741
© NXP B.V. 2010. All rights reserved.
Figure
11).
5 of 52

Related parts for SC16IS741IPW,128