ISP1562BE STEricsson, ISP1562BE Datasheet - Page 57

• Manufacturer Part Number: ISP1562BE
• Manufacturer: STEricsson

Specifications of ISP1562BE

• Operating Temperature (min): -40C
• Operating Temperature Classification: Industrial
• Operating Temperature (max): 85C
• Package Type: LQFP
• Rad Hardened: No
• Lead Free Status / Rohs Status: Supplier Unconfirmed

NXP Semiconductors
Table 86.
Address: Content of the base address register + 54h
ISP1562_3
Product data sheet
Bit
18
17
16
15 to 10
9
8
7 to 5
Symbol
PSSC
PESC
CSC
reserved
LSDA
PPS
reserved
HcRhPortStatus[4:1] - Host Controller Root Hub Port Status[4:1] register bit description
Description
Port Suspend Status Change: This bit is set when the resume sequence is completed. This
sequence includes the 20 ms resume pulse, LS EOP and 3 ms re-synchronization delay. The HCD
can write logic 1 to clear this bit. Writing logic 0 has no effect. This bit is also cleared when Reset
Status Change is set.
0 — Resume is not completed.
1 — Resume is completed.
Port Enable Status Change: This bit is set when hardware events cause the PES (Port Enable
Status) bit to be cleared. Changes from the HCD writes do not set this bit. The HCD can write logic 1
to clear this bit. Writing logic 0 has no effect.
0 — No change in PES.
1 — Change in PES.
Connect Status Change: This bit is set whenever a connect or disconnect event occurs. The HCD
can write logic 1 to clear this bit. Writing logic 0 has no effect. If CCS (Current Connect Status) is
cleared when a Set Port Reset, Set Port Enable or Set Port Suspend write occurs, this bit is set to
force the driver to re-evaluate the connection status because these writes must not occur if the port is
disconnected.
0 — No change in CCS.
1 — Change in CCS.
Remark: If the DeviceRemovable[NDP] bit is set, this bit is set only after a root hub reset to inform
the system that the device is attached.
-
On read Low-Speed Device Attached: This bit indicates the speed of the device attached to this
port. When set, a low-speed device is attached to this port. When cleared, a full-speed device is
attached to this port. This field is valid only when CCS is set.
0 — Port is not suspended.
1 — Port is suspended.
On write Clear Port Power: The HCD can clear the PPS (Port Power Status) bit by writing logic 1 to
this bit. Writing logic 0 has no effect.
On read Port Power Status: This bit reflects the port power status, regardless of the type of power
switching implemented. This bit is cleared if an overcurrent condition is detected. The HCD can set
this bit by writing Set Port Power or Set Global Power. The HCD can clear this bit by writing Clear
Port Power or Clear Global Power. Power Switching Mode and PortPowerControlMask[NDP]
determine which power control switches are enabled. In global switching mode (Power Switching
Mode = 0), only Set/Clear Global Power controls this bit. In the per-port power switching (Power
Switching Mode = 1), if the PortPowerControlMask[NDP] bit for the port is set, only Set/Clear Port
Power commands are enabled. If the mask is not set, only Set/Clear Global Power commands are
enabled.
When port power is disabled, bits CCS (Current Connect Status), PES (Port Enable Status), PSS
(Port Suspend Status) and PRS (Port Reset Status) should be reset.
0 — Port power is off.
1 — Port power is on.
On write Set Port Power: The HCD can write logic 1 to set the PPS (Port Power Status) bit. Writing
logic 0 has no effect.
Remark: This bit always reads logic 1 if power switching is not supported.
-
Rev. 03 — 14 November 2008
HS USB PCI host controller
© NXP B.V. 2008. All rights reserved.
ISP1562
…continued
56 of 93