PCA9698DGG/S911,51 NXP Semiconductors, PCA9698DGG/S911,51 Datasheet - Page 28

• Manufacturer Part Number: PCA9698DGG/S911,51
• Description: IC I/O EXPANDER I2C 40B 56TSSOP
• Manufacturer: NXP Semiconductors

Specifications of PCA9698DGG/S911,51

• Interface: I²C
• Number Of I /o: 40
• Interrupt Output: Yes
• Frequency - Clock: 1MHz
• Voltage - Supply: 2.3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 56-TSSOP
• Includes: POR
• For Use With: OM6281 - DAUGHTER CARD PCA9698 FOR OM6275
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935285491518; PCA9698DGG/S911-T; PCA9698DGG/S911-T

NXP Semiconductors
PCA9698
Product data sheet
Fig 18. Write to the output structure configuration, all bank control, or mode selection
Fig 19. Read from Input Port, Output Port, I/O Configuration, Polarity Inversion, or Mask interrupt registers
The programming becomes effective at the Acknowledge.
If more than 1 byte is written, previous data is overwritten.
If AI = 0, the same register is read during the whole sequence.
If AI = 1, the register value is incremented after each read. When the last register bank is read, it rolls over to the first byte of the
category (see category definition in
The INT signal is released only when the last register containing an input that changed has been read. For example, when
IO2_4 and IO4_7 change at the same time and an Input Port register read sequence is initiated, starting with IP0, INT is
released after IP4 is read (and not after IP2 is read).
SDA
SDA
S A6 A5 A4 A3 A2 A1 A0 0 A
START condition
S A6 A5 A4 A3 A2 A1 A0 0 A
START condition
register determined
by D4 D3 D2 D1 D0
data from register
slave address
first byte
slave address
DATA
acknowledge
acknowledge
from slave
from slave
R/W
A
acknowledge
from master
R/W
Section 7.3 “Command
All information provided in this document is subject to legal disclaimers.
data from register
AI = 1
1
second byte
AI = 'don't care'
X
0 D5 D4 D3 D2 D1 D0
DATA
command register
40-bit Fm+ I
0
Rev. 3 — 3 August 2010
command register
1
0
1
acknowledge
D[5:0] = 00 0000 for Input Port register bank 0
D[5:0] = 00 1000 for Output Port register bank 0
D[5:0] = 01 0000 for Polarity Inversion register bank 0
D[5:0] = 01 1000 for Configuration register bank 0
D[5:0] = 10 0000 for Mask Interrupt register bank 0
from slave
0 D1 D0
register”).
2
C-bus advanced I/O port with RESET, OE and INT
A
A
Sr
acknowledge
from slave
00 for output structure configuration programming
01 for all bank control register programming
10 for mode selection register programming
repeated START
condition
A6 A5 A4 A3 A2 A1 A0
DATA
slave address
data from register
last byte
DATA
A
acknowledge
from slave
P
STOP condition
acknowledge
from slave
R/W
1 A
A
no acknowledge
from master
P
STOP condition
PCA9698
002aab947
© NXP B.V. 2010. All rights reserved.
002aab948
28 of 48