ICS1893CFLF IDT, Integrated Device Technology Inc, ICS1893CFLF Datasheet - Page 66

• Manufacturer Part Number: ICS1893CFLF
• Description: PHYCEIVER LOW PWR 3.3V 48-SSOP
• Manufacturer: IDT, Integrated Device Technology Inc
• Series: PHYceiver™r
• Type: PHY Transceiverr

Specifications of ICS1893CFLF

• Protocol: MII
• Voltage - Supply: 3.14 V ~ 3.47 V
• Mounting Type: Surface Mount
• Package / Case: 48-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 1893CFLF; 800-1021

7.9.1 Next Page (bit 7.15)
7.9.2 IEEE Reserved Bit (bit 7.14)
7.9.3 Message Page (bit 7.13)
7.9.4 Acknowledge 2 (bit 7.12)
7.9.5 Toggle (bit 7.11)
7.9.6 Message Code Field / Unformatted Code Field (bits 7.10:0)
ICS1893CF, Rev. K, 05/13/10
This bit is used by a PHY/STA to enable the transmission of Next Pages following the base Link Control
Word as long as the remote link partner supports the Next Page features of Auto-Negotiation.
This bit is used to establish the state of the Next Page (NP) bit of the Next Page Link Control Word (that is,
the NP bit of the Next Page Link Control Word tracks this bit). During a Next Page exchange, if the NP bit
is logic:
•
•
The ISO/IEC specification reserves this bit for future use. When this reserved bit is:
•
•
IDT uses some reserved bits to invoke auxiliary functions. To ensure proper operation of the ICS1893CF,
an STA must maintain the default value of these bits. Therefore, IDT recommends that an STA always write
the default value of any reserved bits during all management register write operations.
The Message Page (MP) bit (bit 7.13) is used to determine the format or type of Page being transmitted.
The value of this bit establishes the state of the MP bit in the Next Page Link Control Word.
If this bit is set to logic:
•
•
This bit is used to indicate the ability of the ICS1893CF to comply with a message.
The value of this bit establishes the state of the Ack2 bit in the Next Page Link Control Word. If this bit is set
to logic:
•
•
The Toggle (T) bit (bit 7.11) is used to synchronize the transmission of Next Page messages with the
remote link partner. The value of this bit establishes the state of the Toggle bit in the Next Page Link Control
Word. This bit toggles with each transmitted Link Control Word.
If the previous Next Page Link Control Word Toggle bit has a value of logic:
•
•
The initial Next Page Link Control Word Toggle bit is set to the inverse of the base Link Control Word bit 11.
Bits 7.10:0 represent either the Message Code field M[10:0] or the Unformatted Code field U[10:0] bits. The
value of these bits establish the state of the M[10:0] / U[10:0] bits in the Next Page Link Control Word.
Zero, it indicates to the remote link partner that this is the last Message or Page.
One, it indicates to the remote link partner that additional Pages follow this Message.
Read by an STA, the ICS1893CF returns a logic zero.
Written to by an STA, the STA must use the default value specified in this data sheet.
Zero, it indicates that the Page is an Unformatted Page.
One, it indicates to the remote link partner that the Page being transmitted is a Message Page.
Zero, it indicates that the ICS1893CF cannot comply with the message.
One, it indicates to the remote link partner that the ICS1893CF can comply with the message.
Zero, then the Toggle bit is set to logic one.
One, then the Toggle bit is set to logic zero.
ICS1893CF Data Sheet - Release
Copyright © 2009, Integrated Device Technology, Inc.
All rights reserved.
66
Chapter 7 Management Register Set
May, 2010