ICS1893CFLF IDT, Integrated Device Technology Inc, ICS1893CFLF Datasheet - Page 14

• Manufacturer Part Number: ICS1893CFLF
• Description: PHYCEIVER LOW PWR 3.3V 48-SSOP
• Manufacturer: IDT, Integrated Device Technology Inc
• Series: PHYceiver™r
• Type: PHY Transceiverr

Specifications of ICS1893CFLF

• Protocol: MII
• Voltage - Supply: 3.14 V ~ 3.47 V
• Mounting Type: Surface Mount
• Package / Case: 48-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 1893CFLF; 800-1021

4.5 100Base-TX Operations
4.6 10Base-T Operations
4.7 Half-Duplex and Full-Duplex Operations
ICS1893CF, Rev. K, 05/13/10
The ICS1893CF 100Base-TX mode provides 100Base-TX physical layer (PHY) services as defined in the
ISO/IEC 8802-3 standard. In the 100Base-TX mode, the ICS1893CF is a 100M translator between a MAC
and the physical transmission medium. As such, the ICS1893CF has two interfaces, both of which are fully
configurable: one to the MAC and one to the Link Segment. In 100Base-TX mode, the ICS1893CF
provides the following functions:
•
•
•
•
To accurately transmit and receive data, the ICS1893CF employs DSP-based wave shaping, adaptive
equalization, and baseline wander correction. In addition, in 100Base-TX mode, the ICS1893CF provides
a variety of control and status means to assist with Link Segment management. For more information on
100Base-TX, see
The ICS1893CF 10Base-T mode provides 10Base-T physical layer (PHY) services as defined in the
ISO/IEC 8802-3 standard. In the 10Base-T mode, the ICS1893CF is a 10M translator between a MAC and
the physical transmission medium. In 10Base-T mode, the ICS1893CF provides the following functions:
•
•
•
The ICS1893CF supports half-duplex and full-duplex operations for both 10Base-T and 100Base-TX
applications. Full-duplex operation allows simultaneous transmission and reception of data, which
effectively doubles the Link Segment throughput to either 20 Mbps (for 10Base-T operations) or 200 Mbps
(for 100Base-TX operations).
As per the ISO/IEC standard, full-duplex operations differ slightly from half-duplex operations. These
differences are necessary, as during full-duplex operations a PHY actively uses both its transmit and
receive data paths simultaneously.
•
•
For more information on half-duplex and full-duplex operations, see the following sections:
•
•
•
•
Data conversion from both parallel-to-serial and serial-to-parallel formats
Data encoding/decoding (4B/5B, NRZ/NRZI, and MLT-3)
Data scrambling/descrambling
Data transmission/reception over a twisted-pair medium
Data conversion from both parallel-to-serial and serial-to-parallel formats
Manchester data encoding/decoding
Data transmission/reception over a twisted-pair medium
In 10Base-T full-duplex operations, the ICS1893CF disables its loopback function (that is, it does not
automatically loop back data from its transmitter to its receiver) and disables its SQE Test function.
In both 10Base-T and 100Base-TX full-duplex operations, the ICS1893CF asserts its CRS signal only in
response to receive activity while its COL signal always remains inactive.
Section 7.2, “Register 0: Control Register”
Section 7.2.8, “Duplex Mode (bit 0.8)”
Section 7.3, “Register 1: Status Register”
Section 7.6, “Register 4: Auto-Negotiation Register”
ICS1893CF Data Sheet - Release
Section 6.4, “Functional Block: 100Base-TX TP-PMD
Copyright © 2009, Integrated Device Technology, Inc.
All rights reserved.
14
Chapter 4 Operating Modes Overview
Operations”.
May, 2010