ICS1893CFLF IDT, Integrated Device Technology Inc, ICS1893CFLF Datasheet - Page 100
![PHYCEIVER LOW PWR 3.3V 48-SSOP](/photos/6/88/68806/ics1893cflf_sml.jpg)
ICS1893CFLF
Manufacturer Part Number
ICS1893CFLF
Description
PHYCEIVER LOW PWR 3.3V 48-SSOP
Manufacturer
IDT, Integrated Device Technology Inc
Series
PHYceiver™r
Type
PHY Transceiverr
Datasheet
1.ICS1893CFLFT.pdf
(127 pages)
Specifications of ICS1893CFLF
Protocol
MII
Voltage - Supply
3.14 V ~ 3.47 V
Mounting Type
Surface Mount
Package / Case
48-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Drivers/receivers
-
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
1893CFLF
800-1021
800-1021
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ICS1893CFLF
Manufacturer:
IDT
Quantity:
420
Company:
Part Number:
ICS1893CFLF
Manufacturer:
HARVATEK
Quantity:
456
Part Number:
ICS1893CFLF
Manufacturer:
ICS
Quantity:
20 000
Part Number:
ICS1893CFLFT
Manufacturer:
IDT
Quantity:
20 000
9.3 Recommended Component Values *
ICS1893CF, Rev. K, 05/13/10
VDD
Note:
1. The bias resistor networks set the 10baseT and 100baseTX output amplitude levels.
2. Amplitude is directly related to current sourced out of the 10TCSR and 100TCSR pins.
3. Resistor values shown above are typical. User should check amplitudes and adjust for transformer effects
4. The VDD connection to the 18.2K resistor can connect to any VDD. The 18.2K resistor provides negative
Typical Board Layouts
10TCSR and 100TCSR Bias Resistors
Table 9-3. Recommended Component Values for ICS1893CF
† There are two IEEE Std. 802.3 requirements that define the tolerance for the frequency of the oscillator.
Figure 9-1. ICS1893CF 10TCSR and 100TCSR
* For backward compatibillity, refer to the “1893C Alternate Schematic” application note.
Oscillator Frequency
10TCSR Resistor Value
100TCSR Resistor Value
LED Resistor Value
feedback to compensate for VDD changes. Lowering the 18.2K value will lower the 100baseT amplitude.
•
•
Clause 22.2.2.1 requires the MII TX_CLK to have an accuracy of ± 100 ppm.
Clause 24.2.3.4 is more stringent. It requires the code-bit timer to have an accuracy of 0.005% (that is, ±50 ppm).
18
VDD
Parameter
ICS1893CF Data Sheet - Release
2.43KΩ 1%
10TCSR
Copyright © 2009, Integrated Device Technology, Inc.
Minimum
510
–
–
–
10TCSR
19
ICS1893CF
See
All rights reserved.
Typical
2.43k
Figure 9-1
100
25
1k
18.2KΩ 1%
1.82KΩ 1%
100TCSR
Maximum
10k
–
–
–
Chapter 9 DC and AC Operating Conditions
100TCSR
20
± 50 ppm †
Tolerance
1%
1%
–
Units
MHz
May, 2010
Ω
Ω
Ω