PIC18F1220-I/SO Microchip Technology Inc., PIC18F1220-I/SO Datasheet - Page 80

• Manufacturer Part Number: PIC18F1220-I/SO
• Description: Microcontroller; 4 KB Flash; 256 RAM; 256 EEPROM; 16 I/O; 18-Pin-SOIC
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F1220-I/SO

• A/d Inputs: 7-Channel, 10-Bit
• Cpu Speed: 10 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 16
• Interface: USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 18-pin SOIC
• Programmable Memory: 4K Bytes
• Ram Size: 256 Bytes
• Speed: 20 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC18F1220/1320
9.2
The PIR registers contain the individual flag bits for the
peripheral interrupts. Due to the number of peripheral
interrupt sources, there are two Peripheral Interrupt
Request (Flag) registers (PIR1, PIR2).
REGISTER 9-4:
DS39605C-page 78
PIR Registers
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
PIR1: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 1
bit 7
Unimplemented: Read as ‘0’
ADIF: A/D Converter Interrupt Flag bit
1 = An A/D conversion completed (must be cleared in software)
0 = The A/D conversion is not complete
RCIF: EUSART Receive Interrupt Flag bit
1 = The EUSART receive buffer, RCREG, is full (cleared when RCREG is read)
0 = The EUSART receive buffer is empty
TXIF: EUSART Transmit Interrupt Flag bit
1 = The EUSART transmit buffer, TXREG, is empty (cleared when TXREG is written)
0 = The EUSART transmit buffer is full
Unimplemented: Read as ‘0’
CCP1IF: CCP1 Interrupt Flag bit
Capture mode:
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare mode:
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM mode:
Unused in this mode.
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflowed (must be cleared in software)
0 = TMR1 register did not overflow
Legend:
R = Readable bit
-n = Value at POR
U-0
—
R/W-0
ADIF
RCIF
R-0
W = Writable bit
‘1’ = Bit is set
TXIF
R-0
Note 1: Interrupt flag bits are set when an interrupt
2: User software should ensure the appropri-
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
U-0
—
condition occurs, regardless of the state of
its corresponding enable bit or the Global
Interrupt Enable bit, GIE (INTCON<7>).
ate interrupt flag bits are cleared prior to
enabling an interrupt and after servicing
that interrupt.
CCP1IF
R/W-0
 2004 Microchip Technology Inc.
TMR2IF
R/W-0
x = Bit is unknown
TMR1IF
R/W-0
bit 0